User manual SEGA INITIAL D 4

[. . . ] BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain safety: To ensure the safe operation of this product, be sure to read the following before usage. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual close to the product or in a convenient place for future reference. [. . . ] For this task, you will need a Phillips-head screwdriver (for M4 screws), a 2 mm hexagon wrench, an 11 to 12 mm adjustable wrench, wire cutter, knife, wire stripper, soldering iron, and work dryer. 1 Detach the connector. Detach the connector. 02 2 Remove the two screws that secure the VR bracket and lift out the volume with the bracket. SCREW (2) M4x10, w/flat & spring washers VR BRACKET 9-2 FIG. 03 3 Loosen the screws on the gear holder, and detach the gear holder. NUT GEAR HOLDER 321 220-5484 (Same as 220-5753) HEXAGON SOCKET SCREW (2) M4x8 FLAT WASHER SPRING WASHER WIRE COLOR OF POT. 3 = PINK 2 = GREEN 1 = BROWN 9-2 FIG. 04 37 9 CONTROL PANEL 4 5 6 7 8 9 10 11 Remove the nuts that secure the VR bracket, and detach the volume from the VR bracket (see 9-2 FIG. 04). Using wire cutters or a knife, remove the heat-shrinkable tubing that covers the soldered parts. Melt the solder with a soldering gun, and detach the volume from the wires. Cover each wire separately with the heat-shrinkable tubing. Solder the wires to each of the new volume's terminals. Carefully check the wiring schematic when connecting the wires to the volume. Cover the soldered parts with heat shrinkable tubing, and use the dryer to apply heat until the tubing adheres to the soldered parts. Reattach the VR bracket and gear holder to the volume. While the steering wheel is centered, engage the volume axis with the gear, making sure that the D-cut flat side is aligned as indicated in the diagram. Then secure the VR bracket with two screws (see 9-2 FIG 01). Turn the steering wheel and check that the gear moves smoothly. Close the control panel and secure it. Switch on the unit. Be careful not to touch the steering wheel when doing so. After the unit is switched on, the steering wheel undergoes automatic initialization. Configure the volume values on the INPUT ASSIGNMENTS screen in Game Test Mode. It is recommended that the steering wheel volume be set to 80H±8H when the steering wheel is centered. Confirm that when the steering wheel is turned to the left the numbers decrease, and when it is turned to the right the numbers increase (see Service Manual). 9-3 GREASING Use only the specified grease. Using any other kind of grease can result in damage to parts. [. . . ] TFF-0651 TFF-0652 130-5265 280-5275-SR10 601-6231-B010 000-F00408-0B 000-P00508-WB DESCRIPTION SPKR BRKT L SPEAKER COVER SPEAKER BOX W/WOOFER CORD CLAMP SR10 EDGING NEW TYPE (L=10MM) M SCR FH BLK M4×8 M SCR PH W/FS BLK M5×8 19 PARTS LIST ASSY SPKR R (TFF-0660) ITEM NO. TFF-0661 TFF-0652 130-5265 280-5275-SR10 601-6231-B010 000-F00408-0B 000-P00508-WB DESCRIPTION SPKR BRKT R SPEAKER COVER SPEAKER BOX W/WOOFER CORD CLAMP SR10 EDGING NEW TYPE (L=10MM) M SCR FH BLK M4×8 M SCR PH W/FS BLK M5×8 83 ASSY ACCEL&BRAKE (TFF-2200) 19 PARTS LIST ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 101 102 102 104 105 106 201 202 203 204 205 206 207 208 210 211 301 PART NO. SPG-2201 SPG-2202 TFF-2203 SPG-2204 TFF-2205 SPG-2206 SPG-2207 TFF-2208 SPG-2209 SPG-2210 TFF-2211 TFF-2212 SPG-2213X SPG-2214 TFF-2223 TFF-2222 TFF-2224 SPG-2216 AFT-2804 SPG-2219 SPG-2220 SPG-2221 TFF-2225 100-5263 220-5484 220-5753 601-7944 310-5029-F15 280-0419 028-A00304-P 020-000520-0Z 000-P00420 000-P00512-W 000-T00408-0C FAS-450005 000-P00405 FAS-000001 060-F00400 FAS-450025 600-6840-01 DESCRIPTION BASE ACCEL PEDAL BRAKE PEDAL ACCEL SPRING BRAKE SPRING SHAFT ACCEL GEAR BRAKE GEAR NEUTRAL STOPPER VR PLATE ACCEL VR PLATE BRAKE AMPL GEAR GEAR SHAFT STOPPER BRAKE CUSHION BRAKE STOPPER STOPPER ANGLE COVER VR COVER AFT GEAR STAY WSHR NEUTRAL STOPPER D NEUTRAL SPACER B BEARING 12(OILES 80F-1212) VOL CONT B-5K OHM VOL CONT B-5K OHM (TOCOS) GEAR 15 SUMITUBE F F 15MM HARNESS LUG SET SCR HEX SKT CUP P M3X4 HEX SKT H CAP SCR BLK M5X20 M SCR PH M4X20 M SCR PH W/FS M5X12 M SCR TH CRM M4X8 SPR PIN BLK OZ 6X10 M SCR PH M4X5 M SCR TH CRM M3X6 FLT WSHR M4 SPR PIN BLK OZ 8X10 WIRE HARN ACCEL&BRAKE YL NOTE 84 ASSY INPUT SW RUBBER (TFF-1500) 19 PARTS LIST ITEM NO. [. . . ]