User manual SEGA INITIAL D 2 TWIN

[. . . ] Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. [. . . ] GAME TEST MENU MODE Select GAME TEST MODE from the System Menu screen to display the Game Test Menu screen. Use the SERVICE Button to move the cursor to the desired test item. Press the TEST Button to enter the selected item. SYSTEM MENU RAM TEST JVS TEST SOUND TEST C. R. T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING DIMM BOARD TEST NETWORK SETTEING GAME TEST MODE [*****************] -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON GAME TEST MODE INPUT TEST OUTPUT TEST FORCE FEEDBACK INPUT ASSIGNMENTS GAME ASSIGNMENTS CARD R/W TEST CLOSE SETTING BOOKKEEPING BACKUP DATA CLEAR -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON SYSTEM TEST MODE MENU Screen GAME TEST MENU Screen After making changes, be sure to select EXIT and press the TEST Button in order to enable the new settings. Move the cursor to EXIT and press the TEST Button to return to the System Menu screen. www. seuservice. com 46 B. INPUT TEST Select INPUT TEST to display the following screen and check the status of input devices. This test should be used periodically to check that each input device is functioning correctly. GAME TEST MODE INPUT TEST STEERING ACCEL BRAKE GEAR POSITION START CHANGE VIEW SERVICE TEST XXH XXH XXH N OFF OFF OFF OFF PRESS TEST AND SERVICE BUTTON TO EXIT FIG. 3 b INPUT TEST Screen Test the STEERING, ACCEL and BRAKE controls to ensure that they are functioning properly and that the parameters change smoothly as each input device is operated. Display N, UP and DOWN using the GEAR POSITION. N should display there is no control input. Verify that both UP and DOWN display in sync with the position of the shift knob. INPUT ASSIGNMENTS Select INPUT ASSIGNMENTS to display the following screen. GAME TEST MODE INPUT ASSIGNMENTS STEERING: XXX (DEFAULT = 0) ACCEL : XXX (DEFAULT = 0) BRAKE : XXX (DEFAULT = 0) DEFAULT SETTING -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON FIG. 3 ea INPUT ASSIGNMENTS Screen You can adjust each of the menu items by moving the cursor to the menu item and pressing the TEST Button. Return all settings to the default settings with DEFAULT SETTING. STEERING: Make adjustments to STEERING Press the TEST Button to display the following screen. When the "0" displayed is not exactly aligned with the "^" mark above CENTER, use the cursor to select RIGHT or LEFT and move the "0" until it is displayed directly above the "^" mark. Move the cursor to RIGHT and press the TEST Button to move the "0" to the right. Each time you press the TEST Button, "0" moves slightly to the right. Move the cursor to LEFT and press the TEST Button to move the "0" to the left. Each time you press the TEST Button, "0" moves slightly to the left. Move the cursor to EXIT and press the TEST Button to return to the INPUT ASSIGNMENTS screen. GAME TEST MODE STEER ASSIGNMENT (MIN -40 : MAX 40 : DEFAULT 0) STEERING = XXX 0 ^ CENTER RIGHT LEFT -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON FIG. 3 eb STEER ASSIGNMENTS Screen www. seuservice. com 50 ACCEL: Make adjustments to ACCEL Press the TEST Button to display the following screen. [. . . ] TOF-2001 TOF-2500 TOF-2002 TOF-2003 TOF-2004 TOF-2005 TOF-2006 TOF-2007 TOF-2008 TOF-2009 TOF-2150 601-11097 601-11098 TOF-2010 280-5169 280-0419 610-0408-91 601-0460 280-5009-01 030-000820-S 060-F00800 000-T00408-0B 000-P00410-W 008-T00512-0B 000-T00410-0C 000-T00408-0B 050-F01200 FAS-290015 DESCRIPTION CONTROL PANEL BRKT ASSY HANDLE MECHA HANDLE COLLAR CONTROL PANEL COVER SHIFT COVER UPPER SHIFT COVER LOWER COVER HOLDER CUSHION CTRL PNL PLATE WIRE HOLDER ASSY SW PLATE STEERING WHEEL 340 STEERING EMBLEM 340 STICKER STEERING EMBLEM CORD CLAMP TL-20S HARNESS LUG UP/DOWN SHIFTER AL PLASTIC TIE BELT 100 MM CORD CLAMP 21 HEX BLT W/S FLT WSHR M SCR TH BLK M SCR PH W/FS TMP PRF SCR TH BLK M SCR TH CRM M SCR TH BLK M4×8 FLG NUT M12 HEX SKT SCR FH BLK M4×12 NOTE www. seuservice. com 100 Plated yellow ASSY HANDLE MECHA (TOF-2500) Plated black (After installing 6 ) 101 www. seuservice. com Fastening Torque: M3: 0. 74N. m. M4: 1. 8N. m. M6: 5. 6N. m. M8: 17. 4N. m ASSY HANDLE MECHA (TOF-2500) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 101 102 103 104 105 106 201 202 203 204 205 206 207 208 209 210 211 212 PART NO. TOF-2501 TOF-2502 TOF-2503 TOF-2504 TOF-2505 TOF-2507 TOF-2508 TOF-2509X SPG-2505 DYN-1270 TOF-2510 TOF-2511 TOF-2512 TOF-2513 TOF-2514 TOF-2515 601-6172 SPG-2504 SPG-2506 SPG-2453 SPG-2454 ASK-3502 ASK-3503 350-5448-01 220-5484 310-5029-F20 601-11089 100-5168 100-5285 028-A00408-P 030-000820-S 065-S012S0-Z 000-P00410-W 030-000612-S 060-F00600 030-000840-S 068-852216 050-U00800 060-F00800 020-000612-0Z 060-S00600 DESCRIPTION MECHA BASE MECHA BASE LID HANDLE SHAFT SPACER COLLAR A STOPPER BLOCK A SPACER COLLAR B STOPPER PIN SS STOPPER RUBBER SS PULLEY 60 S5M STOPPER KEY SPACER COLLAR C STOPPER HOLDER STOPPER RUBBER STOPPER BOLT VR BRKT GEAR HOLDER GEAR 48 PULLEY 20 S5M MOTOR BRKT KEY 4×4×40 MOTOR SHAFT COLLAR MOTOR SPACER MOTOR COLLAR SERVO MOTOR 500W NEW VOL CONT B-5K OHM SUMITUBE F F 20MM TIMING BELT (150 S5M 520) BEARING 20 (NSK 6904ZZ) BEARING 20(6804ZZ) SET SCR HEX SKT CUP P M4×8 HEX BLT W/S M8×20 STP RING BLK OZ S12 M SCR PH W/FS M4×10 HEX BLT W/S M6×12 FLT WSHR M6 HEX BLT W/S M8×40 FLT WSHR 8. 5-22 ×1. 6 U NUT M8 FLT WSHR M8 HEX SKT H CAP SCR BLK 0Z M6×12 SPR WSHR M6 NOTE www. seuservice. com 102 ASSY ACCEL&BRAKE (SPG-2200) 103 www. seuservice. com ASSY ACCEL&BRAKE (SPG-2200) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 101 102 104 105 106 201 202 203 204 205 206 207 208 209 210 PART NO. [. . . ]