User manual SEGA LET ME DANCE

[. . . ] Make sure to install Dongle prior to LMD program. 1-4. Load blank CD Load blank CD to a dispenser. 1-5. Load CD Case Load CD Case properly below. If you load them improperly, it may cause poor working. Correct Wrong 1-6. [. . . ] JP14 PC : Connecting a PC and a Control board. JP15 CD In Motor : Sending a CD to a CD R/W. JP16 Free Button : Sending a coin signal. (For free service or else) JP17 Reset Button : Reset < Test Button > Testing dispenser's works Take a test as follows. Program error happens not following in order. 1) Case Test : (JP7 performance test) Performing CD Case sampling one time. 2) CDIN Test : (JP15 performance test) Performing CD supplying test one time. CD R/W doesn't work here. ) Performing to a lift a CD from the CD R/W. 4) CD Out Test : (JP1 performance test) Performing a CD dispenser which dispatches a CD to movea exit properly. CD Dispenser CD Dispenser has a function to move a CD recorded as a music video CD to CD exit. CD dispenser performs supplying and putting out a CD to an exit one time on starting LMD program or getting reset back a control board. < Side > < Front > < A : CD R/W > Recording music video to a CD supplied. < B : CD shelf to put out> J1 makes the CD recorded to send a CD exit or C. < C : CD Tray > A poor CD or the CD taken for a test is sent to a CD tray. < J15 : CD In Motor > Sensor checks a backlog of CDs and supplies a CD to a CD R/W on LMD gets started. Lights on at the sensor LED with no CD. < J6 : CD U/D Motor > Lift up a CD which music video recorded from the CD R/W and it makes the CD to dispatch thru B. < JP1 CD out Motor > CD R/W makes the CD from J6 to send CD exit thru B. B makes a proper CD with music video to move to an exit but a poor CD to send a bottom(C). 4-5. CD Case Dispenser CD CASE Dispenser perceives CD case left and it sends a CD case to exit piece by piece. < JP7 Case Motor > Case motor puts out a CD Case piece by piece concurrently a CD out. < JP13 Sensor1 > JP13 Sensor1 perceives whether CD Case remains. < JP3 Park Button, JP4 Setup Button, JP16 Coin Button, JP17 Reset Button > 4-6. Pin-Map < JP2 Bill > < JP5 Coin > < JP9 Print > < JP10 S/W IN > < JP11 DC Power > 5. PC & Accessories Set-Up Follow this instruction for program installation when you should format the PC or reinstall Window XP to the PC. a) Press right on a mouse to go inside to register in desktop. b) Click Customize Desktop after choosing Desktop in Display Properties. c) Unclick as below then pres OK 2) Set-Up Screen Saver a) Click Power after choosing Screen Saver in the tap of Display Properties. b) Select Power Schemes and choose "Never" as below. Then press OK. 3) Set Auto Updates a) Follow in order below then press System Start Settings Control Panel System b) Select "Automatic Update" and click "Turn off Automatic Updates" Then press OK. 4) Set "Service" at "Administrative tools". Start Settings Control Panel Administrative Tools Services b) Double click "Automatic Updates" c) Change "Automatic" into "Disabled" in Startup type and press Stop. And then press Apply. < Before > d) Double click "Security Center" < After > e) Change "Automatic" into "Disabled" in Startup type and press Stop. [. . . ] ( NTSC: USA, Canada / PAL:Europe ) a) Cause : Error message occurs when there is no CD or no CD Case on the screen. b) Solution : Load CDs/Cases to a dispenser. Then counted 1. ) 2) Check Dispenser Check the dispenser within the LMD program. a) Execute MainApp. ini. File (C:\LetmeDance\MainApp_1. 22). [. . . ]