User manual SEGA NAOMI_LINDBERGH VT3 REV1

[. . . ] RND-0073 REV 1 SERVICE MANUAL Incorporating UPRIGHT TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS BEFORE USING THIS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION . 2 2. INTRODUCTION TO THIS SERVICE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. INSTALLATION AND MAINTENANCE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 1. [. . . ] Unscrew the adjusters until they are in contact the floor, and use a wrench to turn them further until the front castors are raised approximately 7mm above the floor. Tighten the locknut on the leg adjusters upwards to lock the legs in position. Ensure adequate ventilation is maintained as detailed below: 12 3. 5. 3. CONNECTION TO THE POWER SUPPLY · Be sure that the machine is not connected to the mains supply before attempting this operation · This operation should only be carried out by QUALIFIED SERVICE PERSONNEL. The AC Unit is located on the right hand side of the base unit, when viewing the screen (as shown in section 3. 3). It houses the IEC inlet, mains switch and fuse, laid out in one of the following assemblies: 2. Ensure that all of the machine's wires have been connected in accordance with the preceding sections and that the mains switch is OFF. Check that the operating voltage of the mains supply matches the machine (section 1. 1). Insert the IEC lead into the IEC inlet and the mains plug into a wall socket. If applicable, switch the wall socket ON. Stand clear of the machine and switch the mains switch ON. 13 3. 5. 4. CREDIT BOARD WIRING TO COIN MECH COIN MECH C220B (TOP ENTRY) GENERIC MECHANICALS LOOM LM1006 OR LM1006IDC LM1008 INSTALLATION · Attach one 15way connector to the C220 coin mech. · Attach the other 15 way connector to Validator A on the credit board. · Attach the blue cable and orange cable to one mech's microswitch. · Attach the blue/green cable and orange/green cable to the other mech's microswitch. · Attach one 15 way connector to Validator A and the other to Validator B on the credit board SECI, C120, SR3 OWN LOOM · Attach the loom to position A on the credit board `EXCEL' TYPE CREDIT BOARD 14 3. 6. MOVING THE MACHINE · When moving the machine, be sure to remove the plug from the power supply. Moving the machine with the plug inserted can cause the power cord to be damaged, resulting in a fire or electric shock. · When moving the machine, retract the leg adjusters fully and ensure the casters make contact with the floor. During movement pay careful attention so that the casters or leg adjusters do not damage any other cabling laid on the floor. Such damage could result in a fire or electric shock. · Do not push the upper part of the cabinet. Failure to observe this can cause the cabinet to fall forwards and result in accidents. · When transporting the machine, be sure to hold the catch portion on the rear of the cabinet with the castors making contact with the surface as shown below. [. . . ] 1 3 4 5 6 7 201 202 PART NUMBER NOA-1500UK-S1 NOA-1503 NOA-1504UK NOA-1505 NOA-1506 NOA-1507 000-P00412-W 012-P03516 QTY 1 1 1 1 2 1 5 4 DESCRIPTION ASSY FRONT PANEL NF LIGHT COVER PRISM PLATE LID GCS LID VMS EMBLEM NAOMI M4X12 MSCR POSI PAN W/FS N6X5/8" S/TAP PAN PAS COMPONENT REFERENCE NOA-1501 + NOA-1502X AS AN ASSY CLIP-IN (5)-5 (4)-4 49 8. 12. NOA-1500HUK ASSY FRONT PANEL (LBG) No. 1 3 4 5 6 7 201 202 PART NUMBER NOA-1500UK-01 NOA-1503 NOA-1504UK NOA-1505 NOA-1506 NOA-1507 000-P00412-W 012-P03516 QTY 1 1 1 1 2 1 5 4 DESCRIPTION ASSY FRONT PANEL PF LIGHT COVER PRISM PLATE LID GCS LID VMS EMBLEM NAOMI M4X12 MSCR POSI PAN W/FS N6X5/8" S/TAP PAN PAS COMPONENT REFERENCE NOA-1501 + NOA-1502-03 AS AN ASSY CLIP-IN (5)-5 (4)-4 50 8. 13. 1 2 101 103 107 108 110 111 201 202 303 304 305 306 PART NUMBER AMK-0162UK AMK-0163UK 400-5457-01 838-13616-91 280-A02048-PM 601-6231-B095 280-A01248-PM 280-A02000-A 010-P00408 010-P00308 NON-60010UK NOA-60011UK NOB-60202UK NON-60012UK QTY 1 1 1 1 4 1 2 1 4 4 1 1 1 1 DESCRIPTION ELEC BASE ELEC BKT SW REGU ATX AUDIO POWER AMP 2CH ROUTER TWIST D20 SO4. 8 P EDGE TRIM NEW TYPE 0. 91t ROUTER TWIST D12 SO4. 8 P ROUTER TWIST D20 ADH M4X8 TAPTITE POSI PAN M3X8 TAPTITE POSI PAN BZ WIRE HARN SW REGU INT WIRE HARN LBG I/O NAOMI WIRE HARN AUDIO POWER-IN WH PSU LBG NAOMI UR COMPONENT REFERENCE [NOT SHOWN [NOT SHOWN] BACK EDGE IN MIDDLE SHOWN] [NOT SHOWN] (101)-4 (103)-4 [NOT SHOWN] [NOT SHOWN] [NOT SHOWN] [NOT SHOWN] [NOT 51 8. 14. [. . . ]