User manual SEGA OUTRUN 2_TWIN

[. . . ] 420-6796-02UK REV 0 SERVICE MANUAL TWIN TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS 1. BEFORE USING THIS PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Incorrect volume setting. Faulty Volume attachment or adjust Adjust the volume attachment and verify in gear alignment. (See Section 3. 9. 2. 2) Faulty connector connection. Check the connections for the Accel and Brake connectors and the connectors between the Accel, Brake and Cabinet. (See 3. 9. 2. 3) Check the connections for the connectors between the I/O Board, the Cabinet and the Control Panel and those inside the Control Panel. The Start button only flashes when Free Play is set. (See Section 3. 15. 8) Reconnect the cables. (See Sections 3. 7. 7 & 3. 15. 8) Failure of the volume. Start button and Change View button input does not work and they do not flash. Faulty connector connections. Start button and Change Unverified settings or operation. View button input works, but they do not flash. Communication cables are wrongly connected. Damage of communication cables. Reconnect cables correctly. (See Section 3. 15. 8) Replace the cables. Contact the company from whom the unit was purchased. 47 3. 15. Gameboard · Turn off the mains power and remove the power cord before opening the machine. · · The GAME BOARD should not require any work to be carried out upon it. All settings and tests can be achieved without access to the GAME BOARD. All work to be carried out by QUALIFIED SERVICE PERSONNEL 3. 15. 1. Removing the Board To return the game board for servicing, take out the board using the following procedure. Unlock the base and remove the 2 M6 bolts. Tip the seat carefully backwards as shown. Be careful not to damage the seat back when resting it on the floor. Use a protective mat under the seat back to protect it on hard floors. Disconnect all connectors from the game board, remove the four screws securing the game board to the wooden base, and lift it out. [. . . ] SPG-2500 ASSY HANDLE MECHA 120 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 101 102 103 104 105 106 107 108 201 202 203 204 205 206 207 208 209 210 211 212 301 PART NO. SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 SPG-2500 QTY 1 1 1 1 1 1 1 1 1 1 3 3 1 1 1 1 2 1 1 1 1 1 3 6 2 1 1 3 4 2 6 4 3 3 1 1 DESCRIPTION HANDLE BASE BASE LID HANDLE SHAFT PULLEY 20 S5M PULLEY 60 S5M MOTOR BRKT VR BRKT STOPPER BOLT STOPPER RUBBER KEY 4X4X40 MOTOR SPACER MOTOR COLLAR STOPPER KEY ADJUST RING MOTOR SHAFT COLLAR SERVO MOTOR 500W NEW BEARING 17 (NSK 6003ZZ) GEAR HOLDER GEAR 48 GEAR 64 TIMING BELT (150 S5M 475) VOL CONT B-5K OHM SUMITUBE F F 20MM SET SCR HEX SKT CUP P M4X8 SET SCR HEX SKT CUP P M3X8 STP RING BLK OZ S12 STP RING BLK OZ S20 M SCR PH W/FS M4X8 M SCR PH W/FS M4X12 HEX BLT W/S M6X12 FLT WSHR M6 U NUT M6 HEX BLT W/S M8X40 FLT WSHR 8. 5-22 X1. 6 U NUT M8 WIRE HARN ASSY HANDLE MECHA VR COMPONENT REF. 121 8. 11. ORT-2100UK-ASSY SW PLATE ITEM 1 2 3 101 102 103 PART NO. ORT-2101 ORT-2102 171-6478B 212-5205-12 509-5560-Y 509-5561-R QTY 1 1 1 1 1 1 DESCRIPTION BUTTON PLATE STICKER START/VIEW PC BD LIGHTING SWX5 CONN JST M 12P RTA PB SW W/L 6V 1L Y LW1L-15VY PB SW W/L 6V 5L R LW5L-15VR COMPONENT REF. 122 8. 12. [. . . ]