User manual SEGA RACE TV

[. . . ] OWNER'S MANUAL IMPORTANT · Before using this product, read this manual carefully to understand the contents herein stated. · After reading this manual, be sure to keep it near the product or in a convenient place for easy reference when necessary. WARRANTIES GAME WARRANTY POLICY Your new SEGA PRODUCT is covered for a period of ninety (90) days from the date of the shipment. This certifies that all Printed Circuit boards, power supplies and monitors are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. [. . . ] The functioning of each SW is as follows: SERVICE BUTTON TEST BUTTON (NOT USED) SOUND VOLUME SWITCH (NOT USED) TEST BUTTON (TEST): SERVICE BUTTON (SERVICE): For the handling of the test button, refer to the following pages. Gives credits without registering on the coin meter. SOUND VOLUME SWITCH (VOLUME): Adjusts sound volume for all of the machines' speakers. 36 COIN METER Open the Coin Door by using the key to have the Coin Meter appear. 9 TEST MODE 37 9-2 SYSTEM TEST MODE · Refer to BOOKKEEPING in GAME TEST MODE for this product's data. 9 TEST MODE · Adjust for an appropriate sound volume in consideration of the installation site. · If the coin meter circuit is removed, play cannot be executed. · Read the LINDBERGH service manual included with the product for details about System Test Mode. However, the settings for this product should follow the specifications in this manual. In the SYSTEM TEST MODE, LINDBERGH board functioning can be checked, the monitor adjusted, and the coin setting performed. Refer to LINDBERGH service manual for the details. Note that the settings of the following items need to be performed in accordance with the instruction given. COIN ASSIGNMENTS COIN CHUTE TYPE: SERVICE TYPE: NETWORK SETTING MAIN NETWORK DHCP: COMMON COMMON DISABLE NOTE: An IP address will be shown, but there is no need to change it. 38 9-3 GAME TEST MODE · When changing the game configuration, changes will not take effect until the Game Test Mode properly after configuration changes. Be sure to exit the Game Test Mode properly after configuration changes. · Do not configure the game in ways not described in this text. It is possible that the game will not function properly. 9 TEST MODE 9-3-1 GAME TEST MODE Menu Select GAME TEST MODE from the System Menu screen to display the Game Test Menu screen. GAME TEST MODE INPUT TEST OUTPUT TEST FORCE FEEDBACK INPUT ASSIGNMENTS GAME ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON 9-3-1 FIG. 01 Use the SERVICE Button to move the cursor to the desired test item. Press the TEST Button to enter the selected item. 9-3-2 9-3-3 9-3-4 9-3-5 9-3-6 9-3-7 9-3-8 INPUT TEST: OUTPUT TEST: FORCE FEEDBACK: INPUT ASSIGNMENTS: GAME ASSIGNMENTS : BOOKKEEPING: BACKUP DATA CLEAR: EXIT: Test each input Test each output Set the STEERING resistance Adjust input settings Adjust game settings View game backup data Clear game backup data Go back to the System Test Menu Move the cursor to EXIT and press the TEST Button to return to the System Menu screen. 39 9-3-2 INPUT TEST Select INPUT TEST to display the following screen and check the status of input devices. This test should be used periodically to check that each input device is functioning correctly. INPUT TEST 9 TEST MODE 9-3-2 FIG. 01 STEERING START VIEW CHANGE BRAKE STEERING GAS BRAKE GEAR POSITION START VIEW CHANGE BOOST SERVICE TEST 00H 00H 00H N OFF OFF OFF OFF OFF PRESS TEST AND SERVICE BUTTON TO EXIT Test the STEERING, GAS and BRAKE controls to ensure that they are functioning properly and that the parameters change smoothly as each input device is operated. Display N, UP and DOWN using the GEAR POSITION. N should display there is no control input. Verify that both UP and DOWN display in sync with the position of the gear shifter. Other controls are working properly if the OFF display changes to ON when operating the corresponding input device. Press the SERVICE and TEST Buttons simultaneously to return to the Game Test Menu Screen. GEAR POSITION BOOST TEST SERVICE GAS NOT USED 9-3-2 FIG. 02 40 9-3-3 OUTPUT TEST Select OUTPUT TEST to display the following screen and check the status of each lamp. This test should be used periodically to check that the lamps are functioning correctly. OUTPUT TEST 9 START BUTTON VIEW CHANGE BUTTON BOOST BUTTON RED LAMP 1 RED LAMP 2 BLUE LAMP 1 BLUE LAMP 2 -> EXIT OFF OFF OFF OFF OFF OFF OFF TEST MODE SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON 9-3-3 FIG. [. . . ] · Even when units are connected for network play, each seat, each game may be given different cost settings. Incorrect cost settings may cause budget balancing problems. The operation of a unit when connected to other units for network play is different than that of a stand-alone unit. Administration of network units should be handled carefully. Entering Test Mode will cause any other machines set up for network play to display the Error screen. [. . . ]