User manual SEGA UFO STOMPER

[. . . ] Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. Indicates that mishandling the product by disregarding this pictograph will cause severe injury or death. [. . . ] This data accumulates unless the backup data is cleared. Total count TOTAL COUNT Total income count Displays total income count until backup is cleared. 1P: 000000 2P: 000000 total coin Total prize-out count Displays total prize-out count until backup is cleared. 1P: 000000 2P: 000000 total prize 11 EXPLANATION OF TEST AND DATA DISPLAY Total play count Displays total play count until backup is cleared. 1P: 000000 2P: 000000 total credit Total payout rate Displays rate calculated from total play count and total prize-out count until backup is cleared. 1P: 000000 2P: 000000 total payout Total service count Displays total service count until backup is cleared. 1P: 000000 2P: 000000 total service Backup data clear (Display when both 1P and 2P in test mode) All data can be cleared. ([Current count] and [Credit] are also cleared) BACKUP DATA CLEAR? 29 DISPLAY FLOW-CHART The screen changes each time the select button is pressed. If no other buttons are pressed and no operations are performed for 60 seconds, the POWER setting screen is restored. When the select button is kept depressed for 2 seconds or longer, [Current count] and [Total count] can be toggled. CURRENT COUNT CURRENT COUNT INCOME SINCE LAST CLEARING 1P:000000 current 2P:000000 coin When in test mode, the following clear screens are displayed. TOTAL COUNT TOTA L COUNT TOTAL INCOME COUNT 1P:000000 total 2P:000000 coin TOTAL PRIZE-OUT COUNT total 1P:000000 prize 2P:000000 TOTAL PLAY COUNT 1P:000000 total 2P:000000 credit TOTAL PLAYONT RATE 1P:000000 total 2P:000000 playout TOTAL SERVICE COUNT 1P:000000 total 2P:000000 service BACKEUP DATA CLEAR B A C K U P D ATA CLEAR? PRIZE-OUT SINCE LAST CLEARING 1P:000000 current 2P:000000 prize 1P 2P PrizeCount 000000 CLEAR?11-3c 31 During test mode, the content for the small 7-seg display are as indicated below. If the limit sensor is entered or operation has just begun, "0" is displayed. TABLE 11-3b Test Mode Number Test mode 1 7-Seg Display Reads 7-seg 1 7-seg 2 7-seg 3 7-seg 4 7-seg 1 7-seg 2 7-seg 3 7-seg 4 7-seg 1 7-seg 2 7-seg 3 7-seg 4 7-seg 1 7-seg 2 7-seg 3 7-seg 4 (Down switch also lights up in response to prize sensor) Content Limit sensor LEFT Limit sensor RIGHT Limit sensor FWD Limit sensor BACK Limit sensor UP Limit sensor DOWN ­­­ ­­­ Open sensor ­­­ ­­­ ­­­ Prize sensor ­­­ ­­­ ­­­ Test mode 2 Test mode 3 Test mode 4 11 EXPLANATION OF TEST AND DATA DISPLAY 32 12 DIP SW SETTINGS Turn off the power supply before changing DIP SW. If the power is left on while DIP SW are changed, electrical shock may occur. IMPORTANT · Make sure the DIP SW that are designated to be OFF are turned OFF. If DIP SW are set to other than prescribed settings, there will be instances when behavior is not suited to actual operations. · Changed settings do not become effective until the power supply has been reactivated after changing DIP SW. · The DIP SW on the game board are not used for game settings but must all be set to OFF. With this product, settings can be changed to those shown in the table by changing the DIP SW (DIP Switch) settings on the switch unit. DIP SW 1 adjusts coin credit settings; DIP SW 2 sets common game operations for 1P and 2P; DIP SW 3 and 4 set the game operations for 1P and 2P, respectively. 12 DIP SW SETTINGS FIG. 12 COIN SETTINGS DIP SW 1~4 Coin credit settings (credits awarded per coin) are set using DIP SW 1. When 9 credits are exceeded, no more coins are accepted and the coins are returned. However, if 1 coin is worth 2 credits or more, and 8 credits are remaining, 10 credits or more are established (10 credits or more can be established, depending on the setting). [. . . ] Secure the ticket bin in place using the 4 flange nuts, secure the wire harness to the cord clamp, then connect the level sensor switch's faston terminal. NOTE: When securing the wire harness, secure the earth wire to the 2 cord clamps backside. Also, make sure there isn't too much slack in the wire harness extending from the cabinet. OPTIONAL ITEMS 21 FASTON TERMINAL WHITE BLACK FIG. 21-5 FASTON TERMINAL CORD CLAMP (3) PHOTO 21-5k 82 22 PARTS LIST (1) TOP ASSY UCU V2 (UCU-00001) (2) ASSY CABINET (UCU-1000-01) (3) ASSY SUB CABINET (UCU-1001-01) (4) CABINET (UCU-1002-01) (15) ASSY GLASS DOOR L (UCU-1100-01) (5) ASSY WIRE (UCU-6002) (16) ASSY GLASS DOOR R (UCU-1110-01) (6) ASSY SPEAKER (UCS-1050X) (17) ASSY BACK LID (UCU-1150) (7) ASSY SERVICE DOOR (UCU-1060) (18) ASSY CTRL PNL PLATE (UCU-2000) (8) SW UNIT (UCU-1070) (19) ASSY X MECHA 1P (UCU-3000) (20) ASSY X MECHA (UCU-3050) (9) AC UNIT (UCU-1080-01) (21) ASSY X MECHA 2P (UCU-3010) (20) ASSY X MECHA (UCU-3050) (10) ASSY PRIZE SENSOR (USS-1200) (22) ASSY Y MECHA (UCU-3100) (11) ASSY FL BASE L (UCU-1300) (23) ASSY Z MECHA (UCU-3200) (12) ASSY FL BASE R (UCU-1310-01) (24) ASSY PIPE (UCU-3300) (13) SIDE FL UNIT (UCU-1320-01) PARTS LIST (25) ASSY UFO MECHA (UCU-3400) (26) ASSY ARM MECHA (UCU-3410X) (14) FLAP UNIT (UCU-1340-01) (27) ASSY REAR COVER (UCS-3450) 22 (28) ASSY MAIN BD (UCU-4000-01) 83 (45) Position for affixing (Opposite side) Left/right height is 647. 5 +/-2 mm PARTS LIST 22 84 (1) TOP ASSY UCU V2 (UCU-00001) In affixing (45) in the left/right direction, use the center as a point of reference. [. . . ]