User manual SEGA VIRTUA COP 2DX SCHEM

[. . . ] Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. [. . . ] (A) (B) (C) (D) REGION The COUNTRY CODE of the MAIN BOARD. BOOT VERSION, QC FIRM VERSION, SC FIRM VERSION Version information for the MAIN BOARD system programmes. This example shows a DIMM BOARD with a GD-ROM DRIVE connected. MEMORY SIZE Capacity of DIMM memory installed on the DIMM BOARD. FIRM VERSION Version information for the DIMM BOARD system programme. Serial number of the DIMM BOARD. (E) (F) (G) 53 www. seuservice. com JVS TEST JVS TEST is used to verify the specs of the I/O BOARD connected to the Chihiro and to run input tests. I/O BOARD specs are displayed initially. Screens may differ depending on the type of I/O BOARD connected to the unit. JVSTEST INPUTTEST NEXTNODE EXIT NODE**** NAME**************** I/OBDJVS Ver**** ********* CMDVER1. 1 JVSVER2. 0 COMVER1. 0 SWITCH2PLAYER(S)13BITS COIN2SLOT ANALOG8CH ROTARY0CH KEYCODE0 SCREENX:0Y:0CH:0 CARD0SLOT HOPPEROUT0CH DRIVEROUT6CH ANALOGOUT0CH CHARACTERCHARA:0LINE:0 BACKUP0 SELECTWITHSERVICEBUTTON ANDPRESSTESTBUTTON Use the SERVICE Button to move the cursor to the desired test item. Move the cursor to INPUT TEST and press the TEST Button to enter the INPUT TEST screen for the I/O BOARD currently displayed. When 2 or more I/O BOARDS are connected, move the cursor to NEXT NODE and press the TEST Button to enter the test screen for the next I/O BOARD. The lower the NODE number, the further away the node is from the Chihiro. Up to 2 COIN CHUTES (#1 and #2) may be used. The (C) COIN TO CREDIT RATE setting for COIN CHUTE #1 and #2 may be set differently. INDIVIDUAL This is for cabinets with individual COIN CHUTES for each player. Coins inserted by each player are treated as individual player credits. The (C) COIN TO CREDIT RATE setting is used by all COIN CHUTES. (B) SERVICE TYPE(COMMON, INDIVIDUAL) Use this to set the function of each SERVICE Button when there is more than one SERVICE Button. COMMON Pressing any SERVICE Button enters service credits for all players. INDIVIDUAL Pressing the SERVICE Button enters service credits only for the corresponding player. www. seuservice. com 58 (C) COIN TO CREDIT RATE Set the CREDIT RATE for each coin inserted. The "X COIN(S) COUNT AS Y CREDIT(S)" setting indicates that "Inserting X coins equals Y credits". Set this to "FREE PLAY" to allow game play without credits. When (A) COIN CHUTE TYPE is set to "COMMON", COIN CHUTE #2 settings are restricted to some extent by the settings for COIN CHUTE #1. DETAIL SETTING This mode allows for more detailed credit rate settings than the (C) COIN TO CREDIT RATE setting. [. . . ] 1 2 3 4 5 6 7 8 9 101 102 103 104 201 202 204 301 302 PART NO. VCT-2101-01 VCT-2102-01 VCT-2103-01 VCT-2104 VCT-2105 VCT-2106 VCT-2107 JPT-2030 125-5124 280-5124-04 310-5029-D20 509-5080 601-0460 000-P00308-W FAS-000099 FAS-000101 VCT-60011 VCT-60012 DESCRIPTION COVER L EXP COVER R EXP HAMMER EXP TRIGGER CHANGE BUTTON SW BRKT COM SPRING SENSOR UNIT TORSION SPRING NYLON CLAMP NK04 SUMITUBE F D 20MM SW MICRO TYPE (SS-5GL2) PLASTIC TIE BELT 100 MM M SCR PH W/FS M3×8 M SCR PH W/SMALL FS BLK M3×10 M SCR PH W/FS M2. 3×10 WH CONTROL UNIT WH CHANGE SW NOTE D-2/2 www. seuservice. com 138 17 SENSOR UNIT (JPT-2030) ITEM NO. JPT-2031 838-13144 012-P00306 DESCRIPTION SENSOR HOLDER SENSOR BD GUN SENSE TAP SCR #2 PH 3×6 NOTE 139 www. seuservice. com 18 SW UNIT (SPY-1170) ITEM NO. SPY-1171 421-8126 509-5028 220-5754 601-0042 310-5029-F20 SPY-60017 DESCRIPTION SW BRKT STICKER SWITCH PANEL SW PB 1M (MIYAMA DS-412R) VOL CONT B5KOHM (RV24YN 15S) KNOB 22 MM SUMI TUBE FF 20MM WH SW UNIT NOTE www. seuservice. com 140 19 METER UNIT (HOD-1590) ITEM NO. [. . . ]