User manual SEGA VIRTUA COP 3 DX

[. . . ] 420-6759-01UK REV 0 SERVICE MANUAL DELUXE TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS 1. BEFORE USING THIS PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1. [. . . ] Replace the parts by disassembling the gun in the following procedure: Also, be sure to perform sighting check in the test mode when the gun parts are replaced. 3. 14. 1. OPERATION 36 3. 14. 2. CONTROL UNIT (GUN CONTROLLER) · Follow these directions carefully to avoid damaging or losing small parts. In the cases where the gun's operation is not satisfactory or the gun sight deviates from the direction in which the control unit is pointed, the gun's interior parts may have been damaged. Replace the parts by disassembling the gun using the following procedure. Note: be sure to perform sighting check in the test mode when the gun parts are replaced. 3. 14. 2. 1. REPLACING THE MICROSWITCH To replace the Gun Controller's internal components, first separate the left shell (Cover L) and right shell (Cover R). The controller's internal components are mounted on the right shell, so work with the gun lying on its right side. To replace the Weapon Change Button microswitch, first remove the Weapon Change Button from the right shell. Remove the 10 screws to separate the two shells. 3. With the right shell lying flat, carefully lift the left shell from the right shell. SCREW (10), black / M3 x 10, W/small flat & spring washers 37 4. Remove the trigger microswitch from the right shell. MICROSWITCH / 509-5080 Remove the soldering and detach the microswitch. 5. 6. Remove the Change Button from the right shell. 7. Remove the spring from the right shell. 38 8. Remove 1 screw and detach the microswitch (with SW bracket attached) from the right shell. SCREW (1) / M3 x 8, W/flat & spring washers 9. Disconnect the microswitch wire connector. 10. Remove the 2 screws and remove the SW bracket from the microswitch. SCREW (2) / M2 x 10, W/flat & spring washers 39 11. Remove the soldering and extract the microswitch. 12. 13. Solder in the new microswitch and reassemble the Gun Controller. Be careful not to tighten the screws too tightly. Test the trigger (or Weapon Change Button) to make sure that the new microswitch functions properly. 40 3. 14. 2. 2. REPLACING THE SENSOR UNIT 1. Follow instructions (1) ­ (3) of "Replacing the Microswitch" to remove the left shell. Detach the connector and pull out the sensor unit. GAMEBOARD · Turn off the mains power and remove the power cord before opening the machine. · To prevent risk of shock or fire, be careful not to damage any wiring. · The GAME BOARD should not require any work to be carried out upon it. All settings and tests can be achieved without access to the GAME BOARD. · Take anti-static precautions to avoid damaging the electronic parts. · All work to be carried out by QUALIFIED SERVICE PERSONNEL. The GD-ROM Service Manual supplied with this product instructs you to remove the Key Chip when shipping the CHIHIRO Board. [. . . ] 1 1 3 3 Description FRONT LID L BLANK FRONT LID BRKT BLANK M4 NUT FLG SER PAS M4 WSHR FORM A FLT BLK Component Reference (2)-3 (2)-3 92 8. 9. HOD-1070UK ASSY SPEAKER ITEM 1 101 201 301 PART NO. CPT-1061UK 130-5096 000-P00512-W HOD-60025 QTY 1 1 2 1 DESCRIPTION SPEAKER BRKT UK ASSY SERVO SPEAKER BOX M5X12 MSCR POSI PAN W/FS PAS WIRE HARN SPEAKER UNIT COMPONENT REF (101)-2 93 8. 10. VCT-1100UK ASSY CONTROLLER CABINET Item 1 2 3 5 6 7 14 18 25 26 27 32 Component Part VCT-2000UK VCT-1103 VTS-HOD-D VCT-1302UK 253-5366 JPT-3101 HOD-1304 DUT-0302UK SPY-1106 HOD-1307-A HOD-1308-A 105-5216 Qty 1 2 1 1 1 2 1 1 2 1 1 2 Description ASSY CTRL PANEL DX HOLDER VTS BOARD HOD GUN HOLDER CABI CASH BOX TUBE CLAMP JOINT PART LID COIN PATH PLATE HOLDER BRKT SIDE BRKT L BLANK SIDE BRKT R BLANK CHAIN BRKT Component Reference CONTINUED NEXT PAGE 94 CONTINUED FROM PREVIOUS PAGE ITEM 201 202 203 204 207 208 PART NUMBER 000-T00416-0B 068-441616-0B 008-T00430-0B 000-T00440-0B 000-P00420-W 030-000630-SB QTY 12 8 8 4 9 12 DESCRIPTION M4X16 MSCR TH BLK M4 WSHR 16OD FLT BLK M4X30 TMP PRF TH BLK M4X40 MSCR TH BLK M4X20 MSCR PAN W/FS PAS M6X30 BLT W/S BLK COMPONENT REFERENCE (1)-8, (7)-4 (1)-8 (12)-8 (14)-4 (3)-4, (18)-5 (25)-8, (26, 27)-4 95 8. 11. VCT-1150UK ASSY FENCE L Item 1 2 3 202 Component Part VCT-1151UK VCT-1152 VCT-1153 FAS-290034 Qty 1 1 1 6 Description FENCE FRAME L DESIGN PLATE L GUARD PLATE L M5 X15 HEX SKT LH CAP SCR STN Component Reference (3)-6 96 8. 12. [. . . ]