User manual SEIKO H024

[. . . ] H024 INSTRUCTIONS INSTRUCTIONS INSTRUCCIONES BEDIENUNGSANLEITUNG ISTRUZIONI INSTRUÇÕES (P. 153) (183 ) English You are now the proud owner of a SEIKO Duo-Display Watch Cal. For best results, please read the instructions in this booklet carefully before using your SEIKO Duo-Display Watch. Please keep this manual handy for ready reference. [. . . ] * When Button C is pressed at the end of timing, the final split time is displayed for 10 seconds with the flashing split display indicator, and then the flashing stops. " Lap time" is the time that has Lap 1 elapsed from the start of one stage of an activity to that of the next stage. "Split time" is the time Start that has elapsed from the start of an activity to any given stage. Split No. 3: 1 min. , 55 sec. 14 C D D C FINAL SPLIT/ STOP D RESET The first 100 lap and split times are automatically stored in memory and can be recalled either during or after the stopwatch measurement. Even if the digits are reset to "00" in the stopwatch measurement, the stored data is not erased and can be recalled unless a new measurement is started. In order to recall lap and split times while timing an event, press Button A to cycle through the 5 different modes. The stopwatch mode indicator (CHR) will continue to flash to indicate that the STOPWATCH mode is in use. A Press to show the MEMORY RECALL mode. Lap 2 Split time A 15 English B Press to select the data (lap time/split time) to be recalled. With each press of Button B, the lap time and split time are displayed alternately. TIMER MODE (TMR) The timer can be set up to 23 hours and 59 minutes in minute increments. (See *8 on page 23) English A time-up warning beep sounds 3 seconds before the set time is up. When the set time is up, time-up beep sounds for 5 seconds. TIMER SETTING A B Press to show TIMER mode. C OR Press for 2 to 3 seconds to show TIMER SETTING display. * The minute digits start flashing. With each press, stored data are recalled from the newest to the oldest. Minute 16 A Press to exit from the MEMORY RECALL mode. D With each press, stored data are recalled from the oldest to the newest. (See *7 on page 23) C D B Press to select an item (flashing) to be adjusted. Press to adjust the selected item. (See *2 on page 22 and *8 on page 23) Press to return to TIMER mode. 17 Hour English TIMER OPERATION ALARM MODE (ALM) English C Two daily alarms work independently. The alarms can be set in minute increments. The alarms can be engaged and disengaged independently of one another. A D Press to show ALARM mode. B D RESET PM indicator for 12-hour display only C Mode indicator C START C STOP C C STOP RESTART * Stop and restart of the timer can be repeated as many times as required by pressing Button C. * A time-up warning beep sounds 3 seconds before the set time is up. When the set time is up, timeup beep sounds for 5 seconds. * If Button D is pressed when the timer is stopped, the display returns to show the set timer time. * The timer will continue to count down even if you move to one of the other 5 modes by pressing Button A. *5 The hourly time signal will not ring while alarm is sounding. 22 *6 Remarks on stopwatch function: · The lap number counts up to "199". After "199", the number is displayed in two digits such as "00" for 200, "00" for 300, and so on. · The split number counts up to "199". After "199", the number is displayed in two digits such as "00" for 200, "00" for 300, and so on. *7 Remarks on memory recall function: · In memory recall after measurement, the oldest measurement in memory is displayed. [. . . ] ** We recommend that you wear a SEIKO Diver's Watch for scuba diving. SHOCKS & VIBRATION Be careful not to drop your watch or hit it against hard surfaces. CARE OF CASE AND BRACELET To prevent possible rusting of the case and bracelet, wipe them periodically with a soft dry cloth. English MAGNETISM The analogue unit of your watch will be adversely affected by strong magnetism, though the digital unit will not be affected. Keep the watch away from close contact with magnetic objects. PERIODIC CHECK It is recommended that the watch be checked once every 2 to 3 years. Have your watch checked by an AUTHORIZED SEIKO DEALER or SERVICE CENTER to ensure that the case, buttons, gasket and crystal seal remain intact. TEMPERATURES Your watch works with stable accuracy within a temperature range of 5°C and 35°C (41°F and 95°F). Temperatures over 60°C (140°F) or below ­10°C (+14°F) may cause a slight time loss or gain or battery leakage or shorten the battery life. [. . . ]