User manual SENNHEISER DW PRO 2

[. . . ] Comfort DECT calls DW Pro1/Pro2 Instruction manual Contents Contents Important safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The DW Pro1/Pro2 wireless headset system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Delivery includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the headset is outside the range of the base station, it will switch off after 30 minutes in order to conserve battery power. Switching the headset on/off If you place the headset into the base station, the headset automatically switches to standby mode. In standby mode, the power consumption is very low and the radiated power is reduced to a minimum. The HEADSET LED lights up blue during charging. Switching the headset on Press and hold the LINK button for 5 seconds. The HEADSET LED flashes blue 3 times and the wireless link to the base station is established (where required). An ascending confirmation beep is heard in the headset. 4 5 Switching the headset off Press and hold the LINK button for 5 seconds. The HEADSET LED flashes red 3 times. Establishing a wireless link between headset and base station To establish a wireless link between headset and base station: Press the LINK button on the headset. The LINK LED ¿ lights up blue and the HEADSET LED flashes blue. 4 To disconnect a wireless link between headset and base station: Press the LINK button on the headset. The LINK LED ¿ and the HEADSET LED go off. 5 23 Using the headset system ³ » You can also establish or disconnect the wireless link by pressing the PC button ³ or the PHONE button » on the base station (depending on the selected mode (PC or Phone), see page 28). If your telephone has a built-in electronic hook switch supporting the MSH standard (see page 13), you can only disconnect the wireless link between headset and base station by placing the headset into the base station. The control signals ("accept a call", "end a call") of the headset are still transmitted to the electronic hook switch without any restrictions. ¿ Putting the headset on and adjusting it Rotate the microphone boom as shown. Carefully bend the flexible microphone boom so that the microphone points towards your mouth. Maintain a distance of about 0. 8-1. 2" (2-3 cm) between the microphone and the corner of the mouth. If you are using the Pro1 headset: Put on the headset so that the ear pad rests comfortably on your left or right ear and that the headband runs over the top of your head. If you are using the Pro2 headset: Put on the headset so that the ear pads ears. rest comfortably on your 7 Left Right Pro1 9 Pro2 9 1 2-3 cm 24 Using the headset system Calling via the fixed line phone using the headset Accepting an incoming call You hear the ring tone of the fixed line phone: Put on the headset and establish a wireless link between headset and base station (see page 23). If you are using a handset lifter/electronic hook switch, the call is automatically accepted. If you receive a call and a handset lifter/electronic hook switch with ring tone detection is used, you hear a ring tone in the headset and the LED of the PHONE button » flashes white. If you are not using a handset lifter/electronic hook switch: Accept the call by lifting the handset or by pressing the "accept call" button on your fixed line phone. Making a call If you are using a handset lifter/electronic hook switch: Dial the desired number. Put on the headset and establish a wireless link between headset and base station (see page 23). The phone connection is established automatically. If you are not using a handset lifter/electronic hook switch: Put the headset on and establish a wireless link between headset and base station (see page 23). Lift the handset and dial the desired number. The phone connection is established. 25 Using the headset system Ending a call Disconnect the wireless link between headset and base station (see page 23). [. . . ] 75 g DECT EU version: CAT IQ 1. 0 Transmission frequency 1, 880 to 1, 900 MHz SAR value US version: DECT 6. 0 1, 920 to 1, 930 MHz 0, 069 W/kg (Pro1 headset) 0, 044 W/kg (Pro1 headset) 0, 058 W/kg (Pro2 headset) 0, 025 W/kg (Pro2 headset) (max. 1 g SAR) 38 Manufacturer Declarations Manufacturer Declarations Warranty Sennheiser Communications A/S gives a warranty of 24 months on this product. For the current warranty conditions, please visit our web site at www. senncom. com or contact your Sennheiser partner. In compliance with the following requirements · · RoHS Directive (2002/95/EC) WEEE Directive (2002/96/EC) Please dispose of this product at the end of its operational lifetime by taking it to your local collection point or recycling center for such equipment. [. . . ]