User manual SENNHEISER EK 300 IEM 01-09

[. . . ] EK 300 IEM Instruction manual Contents Contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The EK 300 IEM G3 diversity receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Areas of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 The frequency bank system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1 Call up "Frequency Preset" Frequency Preset B. Ch: 1. 1 863. 100MHz Select the frequency bank and confirm Frequency Preset B. Ch: 6. 3 824. 500MHz Select the channel; store the setting SET "Stored" When setting up multi-channel systems, please observe the following: Only the factory-preset receiving frequencies within one frequency bank ("1" to "20") are intermodulation-free. It is vital to observe the notes on frequency selection on page 20. Overview of the frequency banks and channels: Frequency bank "1" to "20" "U1" to "U6" Channels up to 16 per frequency bank up to 16 per frequency bank Type System bank: frequencies are factory-preset User bank: frequencies are freely selectable Entering a name ­ "Name" Menu Name Lichael Name Lichael Enter a character and confirm Name Michael Enter a character; store the setting Call up "Name" "Stored" Via the "Name" menu item, you can enter a freely selectable name (e. g. the name of the performer) for the receiver. The name is displayed on the "Frequency/Name" standard display (see page 10). The name can consist of up to 8 characters such as: · letters (without pronounciation marks), · numbers from 0 to 9, · special characters and spaces. To enter a name, proceed as follows: Press the rocker button to select a character. SET Press the SET button to change to the next segment/character or to store the complete entry. 15 Adjusting settings via the operating menu Adjusting the balance ­ "Balance" SET Menu Balance 0 Balance 0 Select the desired setting Balance 5 Store the setting SET Call up "Balance" "Stored" You can adjust the balance in 31 steps. In Focus mode (see next section) and when one of the standard displays is shown, you can also use the rocker button to adjust the balance. The mode of operation of the balance setting depends on the selected audio mode (see next section). Switching between "Stereo" and "Focus" mode ­ "Mode" SET Menu Mode Stereo Mode Stereo Select the desired setting Mode Focus Store the setting SET Call up "Mode" "Stored" The selected audio mode influences the mode of operation of the balance setting (see previous section). Audio mode Stereo The left-right signals are available as usual. The balance setting serves to adjust the balance between the left and right stereo signal. Focus The left-right signals are mixed and are available as a mono signal in both headphone channels. The balance setting serves to adjust the relative levels of the two separate channels in the mixed mono signal. In both audio modes, the corresponding transmitter has to be set to stereo mode! Activating/deactivating the treble boost ­ "High Boost" Via the "High Boost" menu item, you can boost the treble response of the output signal (8 dB at 10 kHz). Output signal remains unchanged High Boost activated EQ EQ Activating/deactivating the automatic lock mode ­ "Auto Lock" SET Menu Auto Lock Active Call up "Auto Lock" Auto Lock Active Select the desired setting Auto Lock Inactive Store the setting SET "Stored" The lock mode prevents that the balance is accidentally adjusted when the receiver is in Focus mode. In addition, the lock mode prevents accidental switching off or programming during operation. The lock mode icon on the current standard display indicates that the lock mode is activated. For information on how to use the lock mode, refer to page 10. 16 Adjusting settings via the operating menu The extended menu "Advanced Menu" To get into the extended menu "Advanced Menu": From the main menu, select "Advanced". Setting the receiving frequencies and the frequency banks "U1" to "U6 ­ "Tune" When you have selected one of the system banks and then select the "Tune" menu, the diversity receiver automatically switches to channel 1 of the frequency bank "U1". In this case, "U1. 1" briefly appears on the display panel. Upon delivery, the channels of the frequency banks "U1" to "U6" are not assigned a receiving frequency. Via the "Tune" menu item, you can set a receiving frequency to be stored in the current channel or you can select a different channel in one of the frequency banks "U1" to "U6" and assign this channel a receiving frequency. Setting a receiving frequency for the current channel Press the rocker button until the "Tune" menu item appears. SET Press the SET button. [. . . ] 90 dB 0. 9% 2 x 100 mW at 32 +8 dB at 80 kHz ­18 dB to ­6 dB, adjustable in steps of 6 dB, can be switched off Overall device Temperature range Power supply Nominal voltage Power consumption: · at nominal voltage approx. 140 mA · with switched-off receiver 25 A ­10°C to +55°C 2 AA size batteries, 1. 5 V or BA 2015 accupack 2. 4 V 24 Manufacturer Declarations Operating time Dimensions Weight (incl. 4 to 6 hrs (depending on volume level) approx. 125 g In compliance with Europe EMC: EN 301489-1/-9 Radio: EN 300422-1/-2 Safety: EN 60065 USA 47 CFR 15 subpart B Approved by Canada Industry Canada RSS 123 IC 2099A-G3SREK300 limited to 806 MHz Connector assignment 3. 5 mm jack plug LR Manufacturer Declarations Warranty Sennheiser electronic GmbH & Co. [. . . ]