User manual SENNHEISER EW 352 G3

[. . . ] 9 Putting the SR 300 IEM G3 transmitter into operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Putting the EK 300 IEM G3 diversity receiver into operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Using the devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Switching the devices on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please observe correct polarity when inserting the batteries/accupack. Close the battery compartment by pressing on the center of the cover µ. The battery compartment cover µ locks into place with an audible click. Charging the accupack To charge the BA 2015 accupack: Insert the diversity receiver into the L 2015 charger (optional accessory). The L 2015 charger can only charge the combination BA 2015 accupack/diversity receiver. Standard batteries (primary cells) or individual rechargeable battery cells cannot be charged. 14 Putting the devices into operation Attaching the diversity receiver to clothing You can use the belt clip to attach the diversity receiver to clothing (e. g. belt, waistband). The belt clip is detachable so that you can also attach the diversity receiver with the antenna pointing downwards. To do so, withdraw the belt clip from its fixing points and attach it the other way round. The belt clip is secured so that it cannot slide out of its fixing points accidentally. To detach the belt clip: Lift one side of the belt clip as shown. Press down the belt clip at one fixing point and pull it out of the receiver housing. Repeat for the other side. 15 Using the devices Using the devices To establish a transmission link, proceed as follows: 1. The transmission link is established. It is vital to observe the notes on frequency selection on page 27. If you cannot establish a transmission link between transmitter and receiver: Make sure that transmitter and receiver are set to the same frequency bank and to the same channel ­ the easiest way is to synchronize the devices (see page 20). If necessary, read the chapter "If a problem occurs . . . " on page 29. Switching the devices on/off Switching the SR 300 IEM G3 transmitter on/off To switch the transmitter on (online operation): Press the STANDBY button ¶. "Unlock?" appears on the display panel. The lock mode is temporarily deactivated: · When you are in the operating menu, the lock mode remains deactivated until you exit the operating menu. · When a standard display is shown, the lock mode is automatically activated after 10 seconds. SET EK 300 IEM G3 receiver SET Press the SET button. Press the rocker button. Press the SET button. 18 Using the devices The lock mode icon of the transmitter or the lock mode icon flashes prior to the lock mode being activated again. B. Ch: 1. 1 ew300IEM of the diversity receiver 519. 150 MHz EQ Standard -18dB 519. 150 MHz ew300 IEM RF AF P MUTE Adjusting the audio channels on the transmitter Via the "Mode" menu item, you can adjust the audio channels. Select "Stereo" if you want to transmit two separate audio signals on channel I and channel II (e. g. channel I = audio signal of the presenter/musician, channel II = sum of all audio signals). Make sure that the receiver's pilot tone evaluation ("Pilot Tone" menu item) is activated. This allows the presenter/musician to adjust the balance between the left and right stereo signal on his receiver. Select "Mono" if you only want to transmit a mono audio signal. In this case, the signal from the left audio input BAL AF IN L is transmitted. During mono operation, you have to deactivate the pilot tone evaluation on the diversity receiver ("Pilot Tone" menu item) in order to ensure that your receiver outputs the same signal on channel I and II. Activating/deactivating the RF signal on the transmitter To deactivate the RF signal: When the standard display is shown on the display panel, press the STANDBY button. "RF Mute On?" appears on the display panel. [. . . ] 980 g In compliance with Europe EMC EN 301489-1/-9 Radio EN 300422-1/-2 Safety EN 60065 Approved by Canada Industry Canada RSS 123, IC: 2099A-G3SREK limited to 806 MHz FCC-Part 74 FCC-ID: DMOG3SREK limited to 698 MHz USA 31 If a problem occurs . . . NT 2-3 mains unit Input voltage Current consumption Output voltage Secondary output current Temperature range 100 to 240 V~, 50/60 Hz max. 120 mA 12 V 400 mA ­10°C to +40°C In compliance with Europe EMC Safety USA Canada EN 55022, EN 55024, EN 55014-1/-2 EN 60065 47 CFR 15 subpart B ICES 003 The mains unit is certified in accordance with the legal safety requirements of Europe, the United States, Canada, Russia and Japan. EK 300 IEM G3 diversity receiver Receiver principle Sensitivity (with HDX, peak deviation) Adjacent channel rejection Intermodulation attenuation Blocking Squelch Pilot tone squelch S/N ratio (1 mV, peak deviation) Max. output power High Boost Limiter Power supply Nominal voltage Power consumption: · at nominal voltage · with switched-off receiver Operating time Dimensions Weight (incl. batteries) adaptive diversity < 1. 6 V for 52 dBArms S/N typ. [. . . ]