User manual SENNHEISER HMD 46

[. . . ] The headset is capable of producing sound pressure levels exceeding 85 dB(A). In many countries 85 dB(A) is the maximum legally permissible level for continuous noise exposure during the working day. Exposure to sounds of higher volume levels or for longer durations can permanently damage your hearing! [. . . ] This headset is capable of producing high sound pressure levels. Higher volumes or longer durations can damage your hearing!Make sure that you can hear critical sounds such as warning alarms. 6 Adjusting the microphone sensitivity The microphone sensitivity has been factory pre-set to 80 mV/Pa. You can change the microphone sensitivity by turning a small screwdriver in the direction of the arrow. + ­ 7 Care and maintenance Cleaning the headset Use a soft, slightly damp cloth to clean the headset from time to time. If the headset is very dirty, use a cloth dampened with mild, soapy water. Do not use any solvents or cleansing agents. Danger of short-circuit due to the ingress of water!Water entering the housing of the headset can cause a short-circuit and damage the electronics. Replacing the earpads For reasons of hygiene, the black earpads should be replaced from time to time. Grasp the edge of the foam earpad behind the earcup as shown and peel it up and away from the earcup. Repeat for the other earcup. 8 Accessories and spare parts By changing the cable, you can simply retrofit your headset (see "Product variants" on page 11). Cable -6 Cable -7 Cable -H-6 Cable -L Cable -PTT-6 Cable -PTT-6-1 Cable -PTT-L Cable -PTT-LA Cable D-3PTT-M Cable E-3PTT-M Headband padding, 1 pair Earpads, 1 pair Earpads, 100 pairs Hygiene pads HZH 46, 200 pairs Wind and pop screen for BKE 46, 1 item Wind and pop screen for BKE 46, any number of items Wind and pop screen for BMD 46, any number of items Cat. 034177 9 Cable clip MZQ 2002 Cable clip HZC 08 Cable clips Cat. 525787 HZC 08 (for round cable only) MZQ 2002 (for round cable or flat cable) 10 Product variants Variant (Cat. No. ) HMD 46-3 (500849) HMD 46-31 (502483) HMD 46-3-6 (500466) HMD 46-3PTT-M (500873) HME 46-3 (500857) HME 46-31 (502484) HME 46-3S (502592) HME 46-3-6 (500467) HME 46-3PTT-M (500874) HME 46-3PTT-6 (500468) HME 46-3PTT-L (500469) HME 46-3PTT-LA (502172) HME 46-ATC (500851) Description Headset with dynamic mic Headset with dynamic mic Headset with dynamic mic Headset with dynamic mic Headset with condenser mic Headset with condenser mic Single-sided round cable ­ ­ with open ends, length 1. 85 m with PTT button and mini DIN plug, length 2. 45 m ­ ­ Single-sided headset ­ with condenser mic Headset with condenser mic Headset with condenser mic Headset with condenser mic Headset with condenser mic Headset with condenser mic Headset with condenser mic with open ends, length 1. 85 m with PTT button and mini DIN plug, length 2. 45 m with PTT button and open ends, length 1. 85 m with LEMO connector FFP. 3S. 310. CLA. 252A, length 1. 85 m with LEMO connector FHG. 2B. 310. CLAD52Z, length 2. 30 m with LEMO connector FFP. 3S. 310. CLA. 252A, length 2 m 11 Cable and connector assignment Headset connector Lato saldato white orange brown green yellow red blue Screen Audio Hi left Audio Hi right Audio Lo left Audio Lo right not assigned Microphone Hi Microphone Lo Screen Cable -6 white orange brown green yellow red blue Screen Audio Hi left Audio Hi right Audio Lo left Audio Lo right not assigned Microphone Hi Microphone Lo Screen Cable -7 (steel wire cable) yellow red gray blue red blue Screen Designed for 2-connector variants Audio Hi left Audio Hi right Audio Lo left Audio Lo right Microphone Hi Microphone Lo Screen 12 Cable -H-6 white orange brown green red blue Screen Audio Hi left Audio Hi right Audio Lo left Audio Lo right Microphone Hi Microphone Lo Screen Cable -L Solder side 1 2 3 2 3 4 49 15 10 8 6 5 7 67 8 9 10 Audio Hi right Audio Lo right not assigned Screen Audio Hi left Audio Lo left Microphone Hi Microphone Lo Bridge to pin 10 Bridge to pin 9 Cable -PTT-6 white orange brown green yellow black red blue Screen Audio Hi left Audio Hi right Audio Lo left Audio Lo right PTT PTT Microphone Hi Microphone Lo Screen approx. 0. 3 m 13 Cable -PTT-6-1 white orange brown green yellow black red blue Screen Audio Hi left Audio Hi right Audio Lo left Audio Lo right PTT PTT Microphone Hi Microphone Lo Screen approx. 1. 0 m HME 46-3PTT-L Solder side 1 2 3 2 3 4 49 15 10 8 6 5 7 67 8 9 10 Audio Hi left Audio Lo left PTT PTT (bridge to pin 10) Audio Lo right Audio Hi right Microphone Hi Microphone Lo Screen PTT (bridge to pin 4) HME 46-3PTT-LA Solder side 1 2 3 6 7 4 8 9 10 5 5 6 4 1 7 3 2 8 9 10 Audio Hi right Audio Lo right PTT PTT / screen / bridge to pin 9 Audio Hi left Audio Lo left Microphone Hi Microphone Lo Bridge to pin 4 / PTT / screen 75- resistor between pin 4 and pin 10 / screen 14 HMD 46-3PTT-M Solder side 1 2 3 4 5 6 7 8 Audio Hi Audio Lo Microphone Hi not assigned not assigned PTT PTT / screen Microphone Lo 8 5 2 7 4 6 3 1 15 Specifications Headphones Transducer principle Ear coupling Frequency response Impedance Characteristic SPL THD Contact pressure Microphone Type Transducer principle Frequency response Output voltage Impedance General data Temperature range Weight without cable HMD 46-3 dynamic, open supra-aural 20­14, 000 Hz 300 per system 95 dB SPL at 1 kHz, 1 mW, mono 83 dB SPL at 1 kHz, 1 V < 1 % at 95 dB SPL (350­3, 000 Hz) approx. 3 N BMD 46-413 dynamic, noise-compensating 100­12, 000 Hz 0. 5 mV/Pa 200 operation: ­15 °C to 55 °C storage: ­55 °C to 70 °C approx. [. . . ] For the current warranty conditions, please visit our web site at www. sennheiser. com or contact your Sennheiser partner. CE Declaration of Conformity This equipment is in compliance with the essential requirements and other relevant provisions of Directive 89/336/EU. The declaration is available on the internet site at www. sennheiser. com. [. . . ]