User manual SENNHEISER MD 516 FE

[. . . ] 6 Overview of the headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview of the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Putting the MD 516 FE into operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connecting the headset to the intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the headset is already paired with a Bluetooth device but the Bluetooth device is switched off or out of range, the LED flashes blue. The headset will try for 3 minutes to connect to one of the up to 8 previously paired Bluetooth devices. If this fails, the Bluetooth function automatically switches off after 10 minutes. MD 516 FE | 17 Using the MD 516 FE Switching the Bluetooth function off Press and hold the multi-function button LED flashes 3 times red. until the If you switch the Bluetooth function off, NoiseGardTM/digital remains switched on. Adjusting the headset to the listening situation Adjusting the volume WARNING Danger of hearing damage!Listening at high volume levels for long periods can lead to permanent hearing defects. Before putting the headset on, set the volume to a low level. Do not continuously expose yourself to high volumes. The control unit features a Master VOLUME slide control which allows you to adjust the volume for the left and right channel separately. Using the Master VOLUME slide control you simultaneously adjust the volume for both ATC communications and your connected Bluetooth device. 1 Use the Master VOLUME slide control to adjust the volume to a comfortable level. 2 Use the Volume button and the Volume button to adjust the volume of your connected Bluetooth device to the volume for ATC communications. 1 2 Vol + Vol ­ Vol + Vol ­ 18 | MD 516 FE Using the MD 516 FE Switching between mono and stereo mode The control unit features a mono /stereo switch F which allows you to switch between mono and stereo mode, depending on the intercom. Do not continuously expose yourself to high volumes. Use the Volume button and the Volume button to adjust the volume of your connected Bluetooth device. When the minimum or maximum volume is reached, you hear an acknowledgement tone. Button Duration Function Incrementally increases the volume Incrementally reduces the volume 1s Continuously increases the volume 1s Continuously reduces the volume 22 | MD 516 FE Using the MD 516 FE Muting connected Bluetooth devices If the MUTING OFF/ON switch is set to the position ON, any Bluetooth transmission is muted once ATC communications have been established. When the ATC conversation is over, the muting is automatically canceled. Set the MUTING OFF/ON switch to the desired position to mute your connected Bluetooth device or to cancel the muting: OFF = muting is canceled ON = muting is activated ON OFF Remote-controlling an audio source If your headset has a Bluetooth connection to an audio source (e. g. iPod, MP3 or CD player), you can use the MD 516 FE to remote-control the audio source as follows: Button Duration Function Plays the track Stops the track (acknowledgement tone) Skips to the next track Skips to the previous track 1s Fast-forwards the track 1s Rewinds the track These functions are not supported by all connected Bluetooth devices. MD 516 FE | 23 Using the MD 516 FE Remote-controlling a mobile phone If your MD 516 FE has a Bluetooth connection to your mobile phone, the LED flashes blue when the mobile phone is ringing. You can also hear the ring tone of your mobile phone in the headset if your mobile phone supports this function. When the mobile phones rings: Button Duration Function Accepts/ends the call 2s Rejects the call (acknowledgement tone) When the mobile phone is switched on, does not ring and you do not make a phone call: Button Duration 1s Function Redials the last number (acknowledgement tone) Activates voice dial 24 | MD 516 FE Using the MD 516 FE During a call: Button Duration 5s Function Transfers the ongoing call back to the mobile phone 2s Activates the muting function (acknowledgement tone) Deactivates the muting function Any button Resetting the settings of the headsets You can reset all settings of your headset to the factory default settings. In doing so, the connection profiles of the Bluetooth devices used are deleted, thus preventing that other users of the headset can access your Bluetooth enabled devices. Press and hold the multi-function button until the LED flashes 3 times red. [. . . ] and any use of such marks by Sennheiser electronic GmbH & Co. Other product and company names mentioned in this instruction manual may be the trademarks or registered trademarks of their respective owners. 36 | MD 516 FE Manufacturer declarations Statements regarding FCC and Industry Canada FCC Declaration of Conformity (DoC) SENNHEISER Model No: MD 516 FE We, Sennheiser Electronic Corporation One Enterprise Drive · Old Lyme · CT 06371 · USA Tel: +1 (860) 434 9190, ext. 144 Fax: +1 (860) 434 1759 declare the above device comply with the requirements of Federal Communications Commission. [. . . ]