User manual SENTROL ZXVFD

[. . . ] How to Use Your Sentrol Security System ZXLCD/ZXVFD Control Station VIEW INFO ALM MEM EVENT LOG OFF CANCEL D 1 BYPASS 2 DELAY ARM 3 CHIME 4 AWAY RST SMOKE 5 TEST 6 PROGRAM 7 QUIT 8 ACCESS 9 INSTANT STAY CLEAR HOME 0 ENTER NEXT NIGHT 1 INTRODUCTION Thank you for choosing the ZX200/ZX210 or the ZX400/ZX410/ZX440F Security Control. This control will provide you with years of reliable operation when properly installed and maintained. To maximize the benefits of your Security System, it is important to carefully read the entire contents of this manual and become familiar with all control operations. Your Security Company Representative has recorded confidential information about your system in this manual, therefore, you should store it in a secure place. [. . . ] Cancelling Exit-ON For Today Program Zone Names Cancels the system from automatically turning ON for Today 10 minutes after you leave the premises for that day only. Allows you to enter a name to each zone. 7 8 Remote Connect Contact your Security Company Representative for instructions. 34 ZX400/ZX410/ZX440F PROGRAMMING Set Clock The clock is set according to military time (24:00 hours). Press 9 . The Control Station will display: TO PROGRAM ENTER PASSCODE 2. Enter passcode: The Control Station will display: SELECT PROGRAM OPTION 1-8 3. Press 2 . The Control Station will display: 10:53 02/04/97 ENTER = COMPLETE 4. (See example) Example: To set the clock to 2:15 pm on June 17, 1997: Press 1 0 CLEAR 4 6 1 1 5 7 (2:15 pm) Press 9 7 (June 17, 1997) 5. Press to start over if a mistake is made or press ENTER to save changes. 35 ZX400/ZX410/ZX440F PROGRAMMING Programming the Automatic-ON Feature (DO NOT enable for UL Listed Systems) This feature allows you to automatically turn your system ON at certain times for certain days. There are four items to be programmed: A. Setting the Security Level Day(s) of week to automatically turn ON Hour to turn ON each day Minute to turn ON each day A. Setting the Security Level To program the Automatic-ON feature: 1. The Control Station will display: TO PROGRAM ENTER PASSCODE 2. Enter passcode: The Control Station will display: SELECT PROGRAM OPTION 1-8 3. The Control Station will display: LOCATION: 00 VALUE: --4. Press 1 ENTER (for location 1). 5. Press . The Control Station will display the current setting. 6. Press 0 for AWAY, press 1 for STAY, or press 2 for NIGHT. Press ENTER to save selection and return to the location prompt. 36 ZX400/ZX410/ZX440F PROGRAMMING B. Day(s) To Turn ON To select the day(s) of the week you want your system to automatically turn ON, add together the values below for those days selected. Value 1 2 4 8 16 32 64 Day of the Week Sunday Monday Tuesday Wednesday Thursday Friday Saturday Example: To have your system automatically turn ON for Monday, Tuesday, and Saturday, add 2 + 4 + 64. Enter the value 70. 8. The Control Station will display: LOCATION: 00 VALUE: --Press 2 ENTER (for location 2). 9. Press . The Control Station will display the current value. 10. Press ENTER to save selection and return to the location prompt. 37 ZX400/ZX410/ZX440F PROGRAMMING C. Hour To Turn ON Each Day If the time scheduled is from 12:00 am to 12:09 am, the ten minute warning period will not begin until 12:00 am and will therefore be less than the set ten minute time period. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]