User manual SHARP 14J1-RU

[. . . ] The illustration of 21J1-RU is used in this operation manual. POWER MENU/ PRESET CH VIDEO AUDIO AV-2 IN (21J1-RU) Bottom CH VCR 75-ohm coaxial cable (round cable) (not supplied) Standard DIN45325 plug (IEC169-2) Antenna in AV-1 IN OUT AUDIO CAUTION : DANGEROUS VOLTAGE INSIDE AV-1 IN OUT AUDIO TO PREVENT ELECTRIC SHOCK. NO UBER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL. VIDEO CAUTION : DANGEROUS VOLTAGE INSIDE TO PREVENT ELECTRIC SHOCK. NO UBER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL. VIDEO POWER To antenna in terminal To RF out terminal Antenna in POWER switch Turns on and off the main power. Power indicator Power can be turned on by the remote control when the indicator is dimly. [. . . ] again to display AUTO mode screen. changes the screen as shown below. MANUAL Normal screen AUTO !Press @ Press CH-SET to call CH-SETTING screen. / CH CH-SETTING POSITION COLOUR SOUND SKIP FINE CH :SELECT :ADJUST CH27 AUTO D/K OFF 168. 25MHz TV/VIDEO MENU/PRESET CH to select desired setting. 1 4 2 5 8 0 3 6 9 • Pressing Language MENU/PRESET # Each time you press SECAM D/K CH CH # Press / on TV set. 1 [ TV set (Bottom) ] CH / , setting for individual items changes as follows: 7 CH CH • All the TV stations in your area that can be received by the TV set are automatically preset between channels 1 to 99. • The screen shows whatever is on channel 1 when auto channel preset is finished. • POSITION The channel position changes to the higher or lower number. • COLOUR FEATURE CH-SET TIMER NORMAL PICTURE CH-SET TV MENU/PRESET AUTO PAL SECAM N443 • SOUND B/G I D/K Manual channel tuning Enables manual channel tuning to a desired TV station. 1 4 2 5 8 0 TV/VIDEO 3 6 9 !Press @ Press MENU/PRESET for more than two seconds. twice to display MANUAL mode changes the screen as shown below. MANUAL Normal screen MANUAL(D/K) VHF 1 48. 25MHz 7 Number buttons • SKIP ON OFF Channel numbers with a “ ” mark on the left are set to SKIP. To turn off SKIP, press the number buttons to select the desired channel and then set “SKIP” to “OFF”. • FINE The frequency changes to allow fine tuning. CH MENU/PRESET CH CH screen. • Pressing Language MENU/PRESET CH FEATURE CH-SET TIMER NORMAL PICTURE AUTO $ Press TV CH-SET to return to normal screen. CH-SETTING POSITION COLOUR AV1 AUTO # Press $ Press / CH or number buttons to select channel position. CH • When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM N443 N358 CH :SELECT :ADJUST / channel position. on TV set to locate channel you wish to preset to current • Search is initiated and when a TV signal is received during the search, the search stops. % Repeat steps 3 and 4 above, to preset channel positions for other broadcasts. ^ Press MENU/PRESET again to display normal screen. • AUTO PRESET stores all receivable channels including those which may be very weak and not clearly visible. Press @ Press # Press on. TIMER to call TIMER screen. / / CH TIMER CH CH to select “ON ”. OFF ON POSITION VOLUME --:-8:00 ----:-- CH FEATURE CH-SET TIMER NORMAL PICTURE to set time for TV to turn TIMER OFF ON POSITION VOLUME --:-8:00 CH28 ---:-- To more bluish background TIMER TV *: TINT can only be selected and adjusted when receiving NTSC broadcasts. (AV only) • WHITE TEMP can only be adjusted on PICTURE menu. • Maximum time that can be preset is 12 hours and 50 minutes. Timer start to count down after setting. $ Press CH / CH to select “POSITION”. ^ Repeat step 4 to 5 above to select and set the “VOLUME”. TIMER OFF ON POSITION VOLUME --:-8:00 CH28 20 --:-- [ TV Set (Bottom) ] & Press * Press TIMER to return to normal screen. to put TV set into Standby mode. Power indicator (Flashing) • Power indicator will flash to indicate On Timer is set. • When the preset length of time setting has passed, the power turns on and a picture appears on the screen. • The ON TIMER speaker volume gradually increases from zero to preset volume. • Pressing NORMAL while a PICTURE selection is displayed, only the selected mode is reset to the standard (factorysetting) position. • Pressing NORMAL while a PICTURE menu screen is displayed will reset all the item of PICTURE menu to the standard (factory-setting) position. • The Off timer is cancelled if the power is turned off or set to the Standby mode using on the remote control or POWER on the TV set, or if the power is otherwise interrupted. • The On Timer is cancelled if the power is turned off using POWER . • If the TV set is turned on by the On Timer, then the TV set will be automatically turned off in two hours if no buttons are pressed on the TV set or remote control. 21J1-RU[EN] 5 7/9/05, 11:22 am E8 TIMER SETTING (Continued) E10 USEFUL FEATURES Reminder on-screen timer Lets you know when a preset length of time has passed by displaying a countdown timer on the screen. This is useful for timer cooking while you watch TV. Channel / Timer display Displays the current channel number, the timer, and other settings on the screen. ! [. . . ] Adjust COLOUR control. VCR To Audio/ Video out terminals Check batteries in the remote control. Try fine tuning to correct. Contrast setting in picture mode might be all the way to the minus side. Press the NORMAL button on the remote control to correct. Increase the volume. • The audiovisual cords required to connect the TV set with video equipment may differ from those shown in the above diagram. [. . . ]