User manual SHARP 21J-FG1SS

[. . . ] Door E3 BEFORE OPERATING TELEVISION Connecting to an antenna To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for coaxial and feeder cables. TV Bottom If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC 169-2), plug it into the antenna jack at the rear of the set. Standard DIN45325 plug (IEC169-2) 75-ohm coaxial cable (round cable) (not supplied) POWER 300-ohm twin-lead flat feeder (not supplied) 75-ohm impedance converter (not supplied) Antenna in If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a 300-ohm to 75-ohm impedance converter and plug it into the antenna jack at the rear of the set. POWER switch Turns on and off the main power. Power indicator Power can be turned on by the remote control when the indicator is dimly. Infrared sensor window Receives the infrared wave from the remote control. MENU/PRESET CH Headphone jack Use to listen to the audio with headphone. [. . . ] twice to display MANUAL mode changes the screen as shown below. MANUAL Normal screen MANUAL(B/G) VHF 1 48. 25MHz 7 Number buttons · SOUND B/G I D/K CH MENU/PRESET CH CH MENU CH screen. · Pressing Language MENU/PRESET SURROUND LANGUAGE NORMAL MENU · SKIP ON OFF Channel numbers with a " " mark on the left are set to SKIP. To turn off SKIP, press the number buttons to select the desired channel and then set "SKIP" to "OFF". · FINE The frequency changes to allow fine tuning. AUTO TV # Press $ Press / CH or number buttons to select channel position. CH ^ Press MENU until normal screen appears. CH-SETTING POSITION COLOUR AV1 AUTO / channel position. on TV set to locate channel you wish to preset to current · Search is initiated and when a TV signal is received during the search, the search stops. · When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM N443 N358 CH :SELECT :ADJUST MENU:RETURN % Repeat steps 3 and 4 above, to preset channel positions for other broadcasts. ^ Press MENU/PRESET again to display normal screen. · SOUND SYSTEM may not have been set correctly, if noise can be heard or if there is no sound. In such case, adjust the SOUND SYSTEM using the MENU on the remote control. · AUTO PRESET stores all receivable channels including those which may be very weak and not clearly visible. To preset only those channels designated for the local viewing region, use MANUAL PRESET. · Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · When using FINE, the channel number changes from green to yellow. E7 SETTING AND ADJUSTMENT (Continued) MENU PICTURE SOUND FEATURE TIMER CH-SETTING E8 TIMER SETTING Picture adjustment !Press MENU @ Press CH # Press $ Press CH % Adjust using to call MENU screen. @ Press CH / CH to select "ON ". # Press / to set time for TV to turn on. · Maximum time that can be preset is 12 hours and 50 minutes. Timer start to count down after setting. TIMER OFF ON POSITION VOLUME --:-8:00 ----:-- CH MENU MENU SURROUND LANGUAGE NORMAL TV TIMER OFF ON POSITION VOLUME --:-8:00 CH28 ---:-- MENU PICTURE SOUND FEATURE TIMER CH-SETTING · Wait for approximately three seconds to return to SOUND menu. ^ Repeat steps 4 and 5 above to adjust other items. & Press MENU until normal screen appears. The following table lists the adjustment items shown in the SOUND menu and how they / . change as you press Selected item SURROUND TREBLE BASS BALANCE To decrease treble To decrease bass To shift balance toward left Press ON - SOUND SURROUND TREBLE BASS BALANCE ON +10 -20 20 $ Press CH / CH to select "POSITION". ^ Repeat step 4 to 5 above to select and set the "VOLUME". TIMER OFF ON POSITION VOLUME --:-8:00 CH28 20 --:-- [ TV Set (Bottom) ] Press ON OFF + + & Press * Press TREBLE +10 + MENU until normal screen appears. to put TV set into Standby mode. Power indicator (Flashing) To increase treble To increase bass To shift balance toward right · Power indicator will flash to indicate On Timer is set. · When the preset length of time setting has passed, the power turns on and a picture appears on the screen. · The ON TIMER speaker volume gradually increases from zero to preset volume. · Pressing NORMAL while a PICTURE/SOUND selection is displayed, only the selected mode is reset to the standard (factory-setting) position. · Pressing NORMAL while a PICTURE/SOUND menu screen is displayed will reset all the item of PICTURE/SOUND menu to the standard (factory-setting) position. · The Off timer is cancelled if the power is turned off or set to the Standby mode using on the remote control or POWER on the TV set, or if the power is otherwise interrupted. · The On Timer is cancelled if the power is turned off using POWER . [. . . ] If outside antenna is used, check for broken wires. Turn OFF using the POWER switch, then turn ON again after a minute. Adjust COLOUR control. Picture weak. No colour. Power Source Power Consumption Dimensions Weight Check batteries in the remote control. · Design and specifications are subject to change without notice. · Receiving system: These receiving systems, encompassing all currently available technology, include those with planned broadcast, videotape and laserdisc hardware and software. Try fine tuning to correct. [. . . ]