User manual SHARP 21JF2-GA

[. . . ] Door E3 BEFORE OPERATING TELEVISION Connecting to an antenna To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for coaxial and feeder cables. TV Bottom If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC 169-2), plug it into the antenna jack at the rear of the set. Standard DIN45325 plug (IEC169-2) 75-ohm coaxial cable (round cable) (not supplied) POWER 300-ohm twin-lead flat feeder (not supplied) 75-ohm impedance converter (not supplied) Antenna in If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a 300-ohm to 75-ohm impedance converter and plug it into the antenna jack at the rear of the set. POWER switch Turns on and off the main power. Power indicator Power can be turned on by the remote control when the indicator is dimly. Infrared sensor window Receives the infrared wave from the remote control. MENU/PRESET CH Headphone jack Use to listen to the audio with headphone. [. . . ] · COLOUR AUTO MENU/PRESET FEATURE CH-SET TIMER NORMAL PICTURE CH-SET PAL SECAM N443 TV · SOUND B/G I D/K Manual channel tuning Enables manual channel tuning to a desired TV station. 1 4 2 5 8 0 TV/VIDEO 3 6 9 !Press @ Press MENU/PRESET for more than two seconds. twice to display MANUAL mode changes the screen as shown below. MANUAL Normal screen MANUAL(B/G) VHF 1 48. 25MHz 7 Number buttons · SKIP ON OFF Channel numbers with a " " mark on the left are set to SKIP. To turn off SKIP, press the number buttons to select the desired channel and then set "SKIP" to "OFF". · FINE The frequency changes to allow fine tuning. CH MENU/PRESET CH CH screen. · Pressing Language MENU/PRESET CH FEATURE CH-SET TIMER NORMAL PICTURE $ Press CH-SET to return to normal screen. CH-SETTING POSITION COLOUR AV1 AUTO AUTO TV # Press $ Press / CH or number buttons to select channel position. CH · When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM N443 N358 CH :SELECT :ADJUST / channel position. on TV set to locate channel you wish to preset to current · Search is initiated and when a TV signal is received during the search, the search stops. % Repeat steps 3 and 4 above, to preset channel positions for other broadcasts. ^ Press MENU/PRESET again to display normal screen. · AUTO PRESET stores all receivable channels including those which may be very weak and not clearly visible. To preset only those channels designated for the local viewing region, use MANUAL PRESET. · Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · When using FINE, the channel number changes from green to yellow. E7 !Press @ Press SETTING AND ADJUSTMENT (Continued) PICTURE E8 TIMER SETTING Picture adjustment PICTURE Off timer Automatically turns power off after a set length of time has passed. 50 0 +10 -10 CONTRAST COLOUR BRIGHTNESS TINT SHARPNESS WHITE TEMP to call PICTURE screen. / CH CH to select adjustment items. Press @ Press # Press off. 50 + TIMER CH to call TIMER screen. / / CH TIMER to select "OFF ". OFF ON POSITION VOLUME --:---:-OFF 0:05 --:-OFF 0:04 to set time for TV to turn TIMER OFF ON POSITION VOLUME 2:30 --:---:-- · Wait for approximately three seconds to return to PICTURE menu. $ Repeat steps 2 and 3 above to adjust other items. % Press PICTURE CONTRAST - · Maximum time that can be preset is 12 hours and 50 minutes. · The ON TIMER speaker volume gradually increases from zero to preset volume. · Pressing NORMAL while a PICTURE selection is displayed, only the selected mode is reset to the standard (factorysetting) position. · Pressing NORMAL while a PICTURE menu screen is displayed will reset all the item of PICTURE menu to the standard (factory-setting) position. · The Off timer is cancelled if the power is turned off or set to the Standby mode using on the remote control or POWER on the TV set, or if the power is otherwise interrupted. · The On Timer is cancelled if the power is turned off using POWER . · If the TV set is turned on by the On Timer, then the TV set will be automatically turned off in two hours if no buttons are pressed on the TV set or remote control. E8 TIMER SETTING (Continued) E10 USEFUL FEATURES Reminder on-screen timer Lets you know when a preset length of time has passed by displaying a countdown timer on the screen. This is useful for timer cooking while you watch TV. Channel / Timer display Displays the current channel number, the timer, and other settings on the screen. ! [. . . ] If outside antenna is used, check for broken wires. Turn OFF using the POWER switch, then turn ON again after a minute. Adjust COLOUR control. Picture weak. No colour. Power Source Power Consumption Dimensions Weight Check batteries in the remote control. · Design and specifications are subject to change without notice. · Receiving system: These receiving systems, encompassing all currently available technology, include those with planned broadcast, videotape and laserdisc hardware and software. Try fine tuning to correct. [. . . ]