User manual SHARP 21JF2-SF

[. . . ] Audio input terminals (AV-2) Connects to a camcorder, video game, etc. Video input terminal (AV-2) Connects to a camcorder, video game, etc. / CH Connecting to an antenna via a VCR You can also connect the TV set to the tuner on a VCR using the connection shown below. TV VCR MENU/PRESET button Tunes the channels. Used for MENU setup. Channel up/down buttons Selects the channels. Tunes or sets the channels. / Volume up/down buttons Adjusts the volume. [. . . ] · Press CH and channels change as shown below. / 2 / 1 / 0 . . . CH CH CH CH FEATURE CH-SET TIMER NORMAL PICTURE @ With the number buttons (on remote control) Displays the channel and timer settings on the screen. 5 · To select a one-digit channel, such as 5, press . If "5-" is indicated, press to select one-digit input, 5 and then press again. · To select a two-digit channel, such as 15, press 1 to select the two-digit input. Press , and then 5 press . TV Resets all settings. -115 PAL B/G Installing batteries in the remote control unit a With your thumbnail, pull up at the slit to open the battery cover. b Insert two batteries (size AA). c Replace the battery cover. Adjusting volume !Adjust volume using / . · The volume bar disappears approximately three seconds after the volume has been adjusted. VOLUME 10 · Channels that have been skipped cannot be selected by CH · The AV1, AV2 input channels cannot be selected using CH these channel. / / CH CH . Use TV/VIDEO to select E6 PRESETTING CHANNELS E7 SETTING AND ADJUSTMENT Auto channel tuning Automatically tunes in and presets receivable TV stations. Channel setting Enables individual channel setting. AUTO(B/G) VHF 1 48. 25MHz !Press @ Press MENU/PRESET for more than two seconds. again to display AUTO mode screen. changes the screen as shown below. MANUAL Normal screen AUTO !Press @ Press CH-SET to call CH-SETTING screen. / CH CH-SETTING POSITION COLOUR SOUND SKIP FINE CH :SELECT :ADJUST CH27 AUTO B/G OFF 168. 25MHz TV/VIDEO MENU/PRESET CH to select desired setting. 1 4 2 5 8 0 3 6 9 · Pressing Language MENU/PRESET # Each time you press PAL B/G CH CH # Press / on TV set. 1 [ Behind the door ] / , setting for individual items changes as follows: 7 CH CH · All the TV stations in your area that can be received by the TV set are automatically preset between channels 1 to 99. Timer start to count down after setting. $ Press CH / CH to select "POSITION". ^ Repeat step 4 to 5 above to select and set the "VOLUME". TIMER OFF ON POSITION VOLUME --:-8:00 CH28 20 --:-- [ TV Set (Bottom) ] & Press * Press TIMER to return to normal screen. to put TV set into Standby mode. Power indicator (Flashing) · Power indicator will flash to indicate On Timer is set. · When the preset length of time has passed, " 0:00" flashes in red. 0:03 0:02 0:01 0:00 CH CH Mute Silences the sound. FEATURE CH-SET TIMER NORMAL PICTURE Flashing !Press TV . " appears on the screen, and the sound E9 FEATURES · Press , " is silenced. Blue screen Automatically turns the screen blue if a broadcast signal is not received. @ Press level. , the volume returns to its previous is pressed at any time. !Press @ Press # Press No signal FEATURE to call FEATURE screen. / to select "BLUE BACK" to "ON" or "OFF". · Mute will be cancelled if the FEATURE BLUE BACK ON FEATURE to return to normal screen. :ADJUST When BLUE BACK is set to "ON". Blue screen TV off (Indicator) after 5 seconds after 15 minutes Standby mode Power indicator lights up dimly · This function also works in the Standby mode. Power is automatically turned on five minutes before the preset length of time expires. The TV set automatically returns to the Standby mode approximately 1 minute if no buttons are pressed on the TV set or remote control. · The Reminder is cancelled if POWER on the TV set is pressed or if the power is otherwise interrupted. [. . . ] · The above recording and editing connections are for intended solely for personal use and not for the illegal copying of audiovisual material protected by copyright laws. E12 TROUBLESHOOTING E13 MODEL SPECIFICATIONS 21JF2-SA World multi 18 system PAL-I PAL-B/G PAL-D/K NTSC 4. 43/5. 5 MHz/60 NTSC 4. 43/6. 0 MHz/60 NTSC 4. 43/6. 5 MHz/60 NTSC 4. 43/5. 5 MHz/50 NTSC 4. 43/6. 0 MHz/50 NTSC 4. 43/6. 5 MHz/50 SECAM-I (6. 0 MHz) Hz Hz Hz Hz Hz Hz SECAM-B/G SECAM D/K, K1 21JF2-GA 21JF2-SM The following problems do not always indicate a hardware failure. Therefore, please use the troubleshooting guide below before calling for repair service. If, after following the guide none of the remedies work, unplug the TV set and call for service. Receiving System TV Broadcasts/ VCR Playback VCR Playback Remote control does not work. Problems Sound OK, picture poor. Picture OK, sound poor. Picture lines or streaks. Picture rolls vertically. No picture or sound. Picture distorted. Picture ghosting. Bars on screen. Quick Service Check List Possible Causes/Remedies Poor reception on some channels. VCR Playback (Using Video-in terminals) Laserdisc Player Playback (Using RF-in terminals) Reception Channels PAL-B/G SECAM-B/G PAL-D/K SECAM-D/K, K1 PAL-I CATV Receiving Frequency Channel Tuning Picture Tube Terminals Sound Output VHF UHF VHF UHF VHF UHF Picture blurred. SECAM-L (French SECAM) PAL 60 Hz NTSC 3. 58 MHz PAL 5. 5 MHz/60 Hz PAL 6. 0 MHz/60 Hz PAL 6. 5 MHz/60 Hz E2­E12 ch E21­E69 ch C1­C12 ch, R1­R12 ch C13­C57 ch, R21­R69 ch B­J ch 21­69 ch (Hong Kong) S1­S20 ch, S21­S41 ch (Hyper) 48. 25 MHz ­ 863. 25 MHz 100-Channel Electronic Tuner with Full Auto Tuning System 21-Inch Flat CRT (53 cm / 51 cm viewable screen size) Audio/video input × 2 (front × 1, rear × 1), Audio/video output × 1 (rear), Headphone jack × 1 (front) 2. 5 W (RMS) × 2, total 5 W (RMS) AC 110 ­ 240V, 50/60 Hz 95 W 605 (W) × 468 (H) × 482 (D) mm 21. 7 kg (Approx. ) Try a new channel to check for possible station trouble. Antenna not connected to terminal at the back of the TV set. [. . . ]