User manual SHARP 21K-FD1SA

[. . . ] To close the door Using the projection, lower the door until closed. Caution: · When opening or closing the door, do not insert your fingers into the gap between the door and front panel. This may result in an injury. Door TV set If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC 169-2), plug it into the antenna jack at the rear of the set. If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a 300-ohm to 75-ohm impedance converter and plug it into the antenna jack at the rear of the set. E3 DVD PLAYBACK Bottom Connecting to a DVD player The DVD input terminals (COMPONENT-IN) on the rear of the TV can be used to input highquality images from a DVD player. DVD input terminals Connecting the video terminals DVD input terminals Y COMPONENT-IN VIDEO PR(CR) DVD player Y or Y/Y PR(CR) or R-Y/Pr ! ! POWER switch Turns on and off the main power. POWER @# $ % % ^ ^& * ( TV Green : To Y Blue : To PB (CB) Red : To PR (CR) Red : To AUDIO IN (R) White : To AUDIO IN (L) PB(CB) PB(CB) or B-Y/Pb @ Power indicator Power can be turned on by the remote control when the indicator is dimly lit. Volume up/down buttons / Adjusts the volume. Makes adjustments in PRESET. CH Channel up/down buttons / CH Selects the channels. Tunes or sets the channels. To colour-difference (component video) out terminals DVD player To audio out (L/R) terminals # Infrared sensor window Receives the infrared wave from the remote control. & Video input terminal (AV-2 IN) Connects to a camcorder, video game, etc. $ MENU/PRESET button Tunes the channels. [. . . ] · A flashing display of the remaining time appears during the last few seconds. When the preset length of time has passed, the TV set enters the Standby mode. TV/VIDEO 1 4 7 2 5 8 0 3 6 9 CH CH On timer Automatically turns power on after a set length of time has passed. CH CH MENU ON (See note below) To more bluish background *: TINT can only be selected and adjusted when receiving NTSC broadcasts. · Auto Noise Reduction (ANR) Noise might be generated on images when playing deteriorated video tapes or when receiving broadcasts with relatively weak signals. In these cases, set ANR to "ON " or "ON " to reduce the noise. However, when receiving good images without noise, you can get better image quality by turning OFF this feature. If ON is selected and the image is still with noise, please switch to ON . · WHITE TEMP can only be adjusted on PICTURE menu. · The CONTRAST, COLOUR, BRIGHTNESS, TINT, SHARPNESS and WHITE TEMP setting can be set differently for individual AV Mode setting. SOUND menu table Selected item AV MODE SURROUND TREBLE BASS BALANCE To decrease treble To decrease bass To shift balance toward left Press DYNAMIC ON - CONTRAST - 50 + !@ Press CH / CH to select "ON ". # Press / to set time for TV to turn on. · Maximum time that can be preset is 12 hours and 50 minutes. Timer start to count down after setting. MENU SURROUND LANGUAGE NORMAL OFF ON POSITION VOLUME --:-8:00 ----:-- TV PICTURE SOUND FEATURE TIMER CH-SETTING OFF ON POSITION VOLUME --:-8:00 CH28 ---:-- [ SOUND menu screen ] Press SOFT ON $ Press CH / CH to select "POSITION". ^ Repeat step 4 to 5 above to select and set the "VOLUME". [ TV Set (Bottom) ] OFF ON POSITION VOLUME --:-8:00 CH28 20 --:-- STANDARD OFF + + AV MODE SURROUND TREBLE BASS BALANCE DYNAMIC ON +10 ­20 20 To increase treble To increase bass To shift balance toward right TREBLE +10 + & Press * Press MENU until normal screen appears. to put TV set into Standby mode. Power indicator (Flashing) · The SURROUND, TREBLE, BASS and BALANCE setting can be set differently for individual AV Mode setting. · Power indicator will flash to indicate On Timer is set. · When the preset length of time setting has passed, the power turns on and a picture appears on the screen. · The ON TIMER speaker volume gradually increases from zero to preset volume. · Pressing NORMAL while a PICTURE/SOUND selection is displayed, only the selected mode is reset to the standard (factory-setting) position. · Pressing NORMAL while a PICTURE/SOUND menu screen is displayed will reset the individual AV Mode setting to the standard (factory-setting) position. · The Off timer is cancelled if the power is turned off or set to the Standby mode using on the remote control or POWER on the TV set, or if the power is otherwise interrupted. · The On Timer is cancelled if the power is turned off using POWER . · If the TV set is turned on by the On Timer, then the TV set will be automatically turned off in two hours if no buttons are pressed on the TV set or remote control. E9 TIMER SETTING (Continued) E10 FEATURES (Continued) TV/VIDEO Reminder on-screen timer Lets you know when a preset length of time has passed by displaying a countdown timer on the screen. This is useful for timer cooking while you watch TV. Child lock Preventing children from watching TV. 1 4 2 5 8 0 3 6 9 !@ Press CH / CH to select " ". # Press / to set time. · Maximum time that can be preset is 12 hours and 50 minutes. [. . . ] If outside antenna is used, check for broken wires. Turn OFF using the POWER switch, then turn ON again after a minute. Adjust COLOUR control. Check batteries in the remote control. · Design and specifications are subject to change without notice. · Receiving system: These receiving systems, encompassing all currently available technology, include those with planned broadcast, videotape and laserdisc hardware and software. Try fine tuning to correct. [. . . ]