User manual SHARP 54GT-25S

[. . . ] Please refer to the operation manual of your VCR for details. TV Antenna RF-Cable OUT Scart-Cable VCR IN PRESETTING THE CHANNELS Manual Channel Preset 1 Press MENU to call the MAIN menu screen. MENU 2 Press CHANNEL UP (oe) or DOWN () to select «<PR>», and press the MENU. MENU 3 Press CHANNEL UP (oe) or DOWN () to select «MANUAL», and press the MENU. MENU 4 Press CHANNEL UP (oe) or DOWN () to select «PR», and select the channel number (1-99) with VOLUME UP (oe) or DOWN () or 0-9 digit buttons. 5 Press CHANNEL UP (oe) or DOWN () to select «BAND» and press MENU to change the position «BAND». (VHL VHH UHF) 3 ENGLISH 6 Press CHANNEL UP (oe) or DOWN () to select «MANUAL» position ( llllllIIllll ). 7 Press VOLUME UP (oe) or DOWN () to start preset. The tuning sequence will stop when a signal is detected, if the signal is not the required channel press again the button to continue 8 Press CHANNEL UP (oe) or DOWN () to select «MEMO», and press MENU to memorize. [. . . ] 4 Repeat steps 2 and 3 above to adjust other items. 5 You can clear the on-screen display by selecting «EXIT» using CHANNEL UP (oe) or DOWN (), and press MENU. MENU NOTE: Selecting «N OFF» you can reset the picture parameters to the factory levels. Press MENU to restore the factory setting «N ON» mode. MENU TIMER SETTING ON Timer Automatically turns power ON after the set length of time has passed. 1 Press MENU to call the MAIN menu screen. 2 Press CHANNEL UP (oe) or DOWN () to select «TIMER», and press MENU. MENU MENU 3 Press CHANNEL UP (oe) or DOWN () to select « L ON» mode. 6 4 Press VOLUME UP (oe) or DOWN () to set the time. ENGLISH 7 5 Press STANDBY/ON (æ) to put the TV set into Standby mode. When the preset of time (in the above example, 8 hour and 30 minutes) has passed, the power turns ON and a picture appears on the screen. NOTE: · In order to know when the ON Timer programme has been run properly, when the TV is in the Standby mode, the ON Timer indicator remains flashing in red. · As a safety precaution, in case nobody is at home when the television switches on automatically, the television will turn itself of automatically after 120 minutes; if it is to continue to run, any button of the remote control functions should be pressed. · In the event of a power cut, disconnection from the plug or the television is switched off at the mains switch, all the data on the ON Timer will be cancelled. OFF Timer Automatically turns power OFF after the set length of time has passed. (ON TIMER) 3 Press CHANNEL UP (oe) or DOWN () to select « L OFF» mode. 4 Press VOLUME UP (oe) or DOWN () to set the time. The timer starts count down. 5 When you have finished setting the time, press MENU. MENU NOTE: In the event of a power cut, disconnection from the plug or the television is switched off at the mains switch, all the data on the OFF Timer will be cancelled. CHILD LOCK (CHANNEL BLOCK) <How to use this system>, You can lock a TV channel to prevent unsupervised TV viewing by following these procedures: 1 Press MENU to call the MAIN menu screen. 2 Press CHANNEL UP (oe) or DOWN () to select «t» menu and press MENU. MENU MENU 3 To select the channel you want to lock with VOLUME UP (oe) or DOWN () (you can also select the channel using 0-9 digit button). 4 Press CHANNEL UP (oe) or DOWN () to select «t» and press MENU. («t» mark will display on top right) MENU 5 Press CHANNEL UP (oe) or DOWN () to select «EXIT», and press MENU. MENU NOTE: You can also protect the SCART connection. HINWEIS: · When you select the channel which you locked, the TV picture will be blue and «t» mark dislays on the screen. · Press (l/t ) button to unlock the channel. [. . . ] Press the TEXT/MIX/PICTURE button a/b/Q to view the subpages. CANCEL button With this button Teletext information is cancelled and TV picture is restored. In this position, the TV programme cannot be changed, being in Teletext/Cancelled mode. [. . . ]