User manual SHARP 70CS-05S

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. LC-20B1U-GBpp01-18 1 02. 2. 21, 4:43 PM ENGLISH IMPORTANT INFORMATION WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. ONLY CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. "Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. " This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www. eia. org IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. [. . . ] CH SEARCH will stop at the current channel and will not add any higher channels. START : EX I T : MENU 5 1 POWER Press MENU to exit. I Adding weak or additional channels or erasing unwanted channels from TV memory Press MENU to display the MENU screen, press ]/[ to move the cursor to SET UP, and press ENTER. Press ]/[ to move the cursor to CH-SETTING, and press ENTER. CH MEMORY CHSETT I NG RETURN A I R/ CABLE CH SEARCH CH MEMORY DISPLAY SLEEP CARD 2 ENTER/ ]/[/ </ > ENTER 3 4 5 MUTE BRIGHT MENU TV/VIDEO Press ]/[ to move the cursor to CH MEMORY, and press ENTER. Use ]/[ or Channel Select to select each desired channel to add or erase. Press > to add the channel to the TV's memory or press < to erase the channel from the TV's memory. Press MENU to exit. AIR 2 FLASHBACK VOL CH 1 4 7 MTS 2 5 8 0 3 6 9 100 MENU TO ADD : > to add channel 2 to the TV memory EX I T : MENU < to erase channel 2 to the TV memory Channel Select 6 CH MEMORY AIR 2 TO ERASE : Note : G If CH SEARCH is performed again, the previously memorized channels will be lost. EX I T : MENU 26 LC-20B1U-GBpp19-35 26 02. 2. 21, 4:42 PM ADJUSTMENT (Continued) Adjusting the BLUE SCREEN Settings I BLUE SCREEN Automatically turns the screen blue if a broadcast signal is not received. 1 POWER Press MENU to display the MENU screen. Press ]/[ to move the cursor to SET UP, and press ENTER. 2 DISPLAY CARD ENTER MENU SLEEP T IMER V I DEO ADJUST PRESET CLOSED CAPT I ON VCH I P BLOCK SET UP SLEEP MUTE BRIGHT MENU TV/VIDEO SELECT : ENTER : ENTER EX I T : MENU FLASHBACK VOL CH ENTER/ ]/[/ </ > MENU 3 1 4 7 MTS 2 5 8 0 3 6 9 100 Press ]/[ to move the cursor to BLUE SCREEN, and press ENTER. SET UP RETURN BLUE SCREEN [ ON ] LANGUAGE CHSETT I NG SELECT : ENTER : ENTER EX I T : MENU 4 5 Press </ > to select ON or OFF, and press ENTER. Press MENU to return to the main screen. SET UP RETURN BLUE SCREEN [ OFF ] LANGUAGE CHSETT I NG ADJUST : ENTER : ENTER EX I T : MENU Note G G G When received signals are weak or interfered with by some other signals, the BLUE SCREEN function may be activated. To watch the TV under such conditions, set BLUE SCREEN to OFF. When the AV-IN1, AV-IN2 or COMPONENT input mode is selected, if no signal is being input, the BLUE SCREEN function is activated. The BLUE SCREEN function is inactive in CARD mode. 27 LC-20B1U-GBpp19-35 27 02. 2. 21, 4:42 PM ADJUSTMENT (Continued) Adjusting the CLOSED CAPTION Settings I SETTING CLOSED CAPTION This TV set is equipped with an internal Closed Caption decoder. "Closed Caption" is a system which allows conversations, narration, and sound effects in TV programs and home videos to be viewed as captions on the TV screen (see the illustration). : The content rating can be set. TV PARENTAL GUIDELINES (examples) Example 1: When TV-Y7 in the age-based rating is set to BLOCK, this will automatically block the higher ratings: TV-G, TV-PG, TV-14 and TV-MA. In addition, D, L, S, V and FV in CONTENT are automatically blocked unless you manually set BLOCK CONTENT. Example 2: When no item in the age-based rating is blocked, D in the content-based rating will be automatically blocked. Note G G G Age-based ratings can be modified by the content-based ratings, but only in the combinations indicated by an X in the table above. Choosing a lower age-based rating blocks the higher age-based ratings regardless of content rating settings. If you set TV-Y and TV-Y7 to BLOCK, CONTENT will display all items. 30 LC-20B1U-GBpp19-35 30 02. 2. 21, 4:43 PM ADJUSTMENT (Continued) Adjusting the V-CHIP Settings (Continued) I SETTING V-CHIP [1] MPAA RATING 1 POWER DISPLAY SLEEP CARD Press MENU to display the MENU screen. MENU SLEEP T IMER V I DEO ADJUST PRESET CLOSED CAPT I ON VCH I P BLOCK SET UP ENTER MUTE BRIGHT MENU TV/VIDEO FLASHBACK VOL CH ENTER/ ]/[/ </ > MENU 2 Press ]/[ to move the cursor to V-CHIP BLOCK, and press ENTER. 1 4 7 MTS 2 5 8 0 3 6 9 100 MENU SLEEP T IMER V I DEO ADJUST PRESET CLOSED CAPT I ON VCH I P BLOCK SET UP Channel Select 3 INPUT SECRET NO. Input the 4-digit secret number by using the channel select keys. I NPUT SECRET NO . 4 Press ]/ [ to move the cursor to MPAA, and press ENTER. VCH I P BLOCK RETURN MPAA TV GU I DEL I NES STATUS [ OFF ] SELECT : ENTER : ENTER EX I T : MENU 5 Press ]/[ to move the cursor to PG, and press ENTER. MPAA RETURN G [ ] PG [ ] PG13 [ ] R [ ] NC 17 [ ] X [ ] SELECT : ENTER : ENTER EX I T : MENU 6 Press </ > to select BLOCK, and press ENTER. If you set PG to BLOCK, PG-13, R, NC-17 and X are automatically blocked. Press MENU to return to the main screen. 7 Note G G MPAA RETURN G [ ] PG [ BLOCK ] PG13 [ BLOCK ] R [ BLOCK ] NC 17 [ BLOCK ] X [ BLOCK ] ADJUST : ENTER : ENTER EX I T : MENU If you set G to BLOCK, all ratings are automatically blocked. If you set X to BLOCK, G, PG, PG-13, R and NC-17 are not blocked. 31 LC-20B1U-GBpp19-35 31 02. 2. 21, 4:43 PM ADJUSTMENT (Continued) Parent Control (V-CHIP Operation Continued) Adjusting the V-CHIP Settings (Continued) [2] TV GUIDELINES I Setting MPAA 1 2 POWER DISPLAY SLEEP CARD Repeat steps 1 to 3 of [1] MPAA RATING. Press ]/[ to move the cursor to TV GUIDELINES, and press ENTER. VCH I P BLOCK RETURN MPAA TV GU I DEL I NES STATUS [ OFF ] ENTER MUTE BRIGHT MENU TV/VIDEO FLASHBACK VOL CH ENTER/ ]/[/ </ > MENU SELECT : ENTER : ENTER EX I T : MENU 1 4 7 MTS 2 5 8 0 3 6 9 100 3 Press ]/[ to move the cursor to TV-Y7, and press ENTER. TV GU I DEL I NES RETURN TVY [ ] TVY7 [ ] TVG [ ] TVPG [ ] TV 14 [ ] TVMA [ ] BLOCK CONTENT [ SELECT : ENTER : ] ENTER EX I T : MENU 4 Press </ > to select BLOCK, and press ENTER. If you set TV-Y7 to BLOCK, TV-G, TV-PG, TV-14 and TV-MA are automatically blocked. [. . . ] Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply. [. . . ]