User manual SHARP AJ-6020

[. . . ] MODEL AJ-6020 COLOUR INKJET MULTIFUNCTION SETUP GUIDE AND OPERATION MANUAL Page INTRODUCTION SETTING UP THE UNIT LOADING PAPER INSTALLING THE SOFTWARE OPERATION PANEL MAKING COPIES FUNCTIONS SET BY THE USER USING THIS UNIT WITH YOUR COMPUTER USER MAINTENANCE TROUBLESHOOTING APPENDIX 4 6 20 25 46 49 63 69 71 78 84 This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modefiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG. [. . . ] Select this type when copying onto Cardstock paper. 53 MAKING SELECTIONS FOR COPYING 3 Press the "ENTER" button. A checkmark ( ) will appear, indicating the selected paper type. After displaying the selected value for one second, the display will return to the ready message. 1. Paper Type 2. Coated Paper How to set the paper size 1 Press the "PAPER SELECT" button, and repeatedly press the or "ARROW" buttons until the "Paper Size" setting is displayed on the first line of the display panel. 2. Paper Size 3. A4 2 Repeatedly press the or "ARROW" buttons to display the paper size to be used on the second line of the display. Select from "1. B5". 3 Press the "ENTER" button. A checkmark ( ) will appear, indicating the selected size. After displaying the selected value for one second, the display will return to the ready message. 2. Paper Size 4. A5 When using the bypass tray for copying, insert only one sheet of paper at a time and then press the "START" button ( ). The paper will be automatically fed into the unit, and copying will start. You cannot make multiple copies using the bypass tray. When using card stock type paper or thick paper for copying, set the paper knob to ( ). (See page 21) 54 MAKING SELECTIONS FOR COPYING How to set the copy quantity A single copy can be made with the default setting, i. e. , when "0" is displayed. Use the ( ), ( ) "COPY QUANTITY" buttons to set the copy quantity. Set the number of copies using the increase ( ) / decrease ( ) buttons. Repeatedly pressing the buttons will increase/decrease the display in increments of 1. If either button is pressed and held down, the display will change in increments of one until 5 is reached and then will change in increments of 5. 15, 20 . . . ) During Copying During copying, the copy quantity display will decrease by 1 each time a copy is made. Example: If the number of copies is set to "2". Copying. . . 100% A4 1 Ready to Copy 100% A4 2 First page completed Second page completed !To cancel a multiple copy job, press the "CLEAR/STOP" button ( ). !You can set the number of copies up to 50. If you want to change the number of copies, press the "CLEAR/STOP" button ( ) and set the required number of copies. How to select colour or black/white copy You can switch modes by pressing the "COLOUR MODE" button. When the upper colour mode indicator is illuminated, the unit will copy in multicolour. When the lower indicator is illuminated, the unit will copy in black and white. Default setting is "COLOUR" How to select the copy quality Copy quality can be selected in four increments. You can select the copy quality by pressing the "COPY QUALITY" button. The selections allow you to trade off between speed and image quality. Default setting Example: Moving the indicator upward increases the speed but decreases the image quality. !Some of the quality settings cannot be selected depending on the "Paper Type". [. . . ] Upon termination you must destroy the Software and related documentation and all copies thereof. 4. Export Law Assurances. You agree and certify that neither the Software nor any other technical data received from SHARP, nor the direct product thereof, will be exported outside the United States except as authorized and as permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree that you will not re-export the Software nor any other technical data received from SHARP, nor the direct product thereof, except as permitted by the laws and regulations of the United States and the laws and the regulation of the jurisdiction in which you obtained the Software. 5. Government End Users. If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provisions apply. [. . . ]