User manual SHARP AL-1045/1217/1255/1456/1457/1555 ONLINE MANUAL

[. . . ] These can be re-used for transporting the machine, should it be necessary. 1 2 3 4 5 6 7 8 9 10 Original cover 11 Side cover 12 Manual bypass 13 Paper guides 14 Side cover open button 15 Front cover 16 Paper tray 17 Operation panel 18 Original table 19 Cover for optional printer interface 20 Paper output tray Paper output tray extension Handle Power switch Power cord socket TD cartridge lock release button TD cartridge Drum cartridge Drum cartridge handle Transfer charger 21 Charger cleaner 22 Fusing unit release tab 23 Paper feed roller 24 SPF exit area* 25 Original guides* 26 Document feeder tray* 27 Feeding roller cover* 28 Bypass tray (AL-1200, AL-1220) 29 Bypass tray guides (AL-1200, AL-1220) * AL-1220 only 3-12) 2 Light ({) and dark (}) keys and exposure indicators Use to adjust the MANUAL (=) or PHOTO ( ) exposure level. Q Paper feed location indicator Light up to show the selected paper feed station. W Zoom keys (N, L) Use to select any reduction or enlargement copy ratio from 50 to 200% in 1% increments. [. . . ] To reset the ratio to 100%, press the copy ratio selector key repeatedly until the 100% indicator lights up. To select a zoom ratio: When a zoom (N or L) key is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the display. In order to quickly change the zoom ratio, press and hold down the (N or L) key. the displayed setting will stop on any preset reduction or enlargement setting. To further reduce or raise the zoom ratio, firstly release the key and then press and hold down. Set the number of copies using the copy quantity (<, <) keys and press the print ( ) key. The singlesheet manual bypass and the bypass tray (AL-1200, AL-1220) can be used to feed standard paper, transparency film, labels and other special purpose papers measuring from A6 to A4 and in the weight range of 52 to 128 g/m². For booklet binding, turn the first copy over top to bottom (not shown). Feed the first copy into the manual bypass or into the bypass tray (AL-1200, AL1220). Be sure to feed the copy paper one sheet at a time. Power save modes (page 3-20) The copier has two power save modes of operation: preheat mode and auto power shut-off mode. Press the light ({) or dark (}) key to return to the normal copy mode. Be sure to use only genuine SHARP parts and supplies. The TD cartridge replacement required (s) indicator will light up when toner is needed. for more information on purchasing the TD cartridge , see SUPPLY PART NUMBERS AND STORAGE on page 3-36. If copying is continued while the indicator is lit, copies will gradually become lighter until the copier stops and the indicator begins blinking. Replace the old TD cartridge by following the procedure given below. After the copier stops, it may be possible to make a few more copies by taking the TD cartridge out of the copier, shaking it horizontally, then reinstalling it. If copying is not possible after this operation, replace the TD cartridge. During a long copy run of a dark original, the ready ( ) indicator may blink, the s indicator light up, and the copier stop, even though toner is left. The copier automatically replenish the toner level for up to 2 minutes and then the ready ( ) indicator will light up. Ensure that the bypass tray is open (AL-1200, AL-1220) and then open the side cover while pressing the side cover open button. [. . . ] Copy ratio Exposure system Copy paper feed Fusing system Development system Light source Resolution Scan: Gradation Scan: Memory: Power supply Power consumption Overall dimensions Weight Copier dimensions Operating conditions Humidity: Noise level First-copy time may differ depending on operating conditions, such as power-supply voltage and room temperature. The values for copy speed are rounded to the nearest whole number. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. the performance specification figures indicated are nominal values of production units. [. . . ]