User manual SHARP AL-1530

[. . . ] mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] * The auto clear time varies with a user program setting. Preheat mode and auto power shut-off mode will be canceled when printing is started. If the paper size specified from the software application is larger than the paper size in the printer, the image may be printed onto two sheets of paper. If the paper size specified from the software application is larger than the paper size in the printer, part of the image that is not transferred to the paper may remain on the surface of the drum. In this case, the backside of the paper may become dirty. If this occurs, change to the correct size paper and print two or three pages to clean the image. q q 2 Printing q q q Indicators on the operation panel The ON LINE indicator and the ready ( ON LINE indicator Power save indicator ) indicator indicate the state of the printer. Ready indicator On: Indicates the printer is ready for printing (on line), data is being received from a computer or printing is being performed. Off: Indicates copying is being performed or the printer is in the auto power shut-off mode. ON LINE indicator On: Indicates the printer is ready for printing (on line) or printing is being performed. Blinking: Indicates copier setting is being performed during printing or data is being received from a computer. Power save indicator On: Indicates the printer is in a power save mode. Ready indicator SETTING PRINT CONDITIONS FROM PRINTER DRIVER The setting method and setting items of the printer driver are described below. Before setting the printer driver, check the following items. The SHARP AL-1000 Series printer driver has been installed in the computer to be used. If not, see INSTALLING THE PRINTER DRIVER SOFTWARE on page 10. The SHARP AL-1000 Series has been selected as the default printer on the computer to be used. 18 SETTING PRINT CONDITIONS FROM PRINTER DRIVER Windows 95/Windows 98/Windows NT 4. 0: Click the Start button of the computer and then select Printers from Settings. 1 2 If you use Windows 95/Windows 98, right-click the SHARP AL-1000 Series icon in the Printer folder and select Properties in the menu. If you use Windows NT 4. 0, right-click the SHARP AL-1000 Series icon in the Printer folder and select Document defaults in the menu. For this description, it is assumed that the mouse is configured for right hand operation. 2 Printing 3 The properties of the SHARP AL-1000 Series printer driver will be displayed. If you use Windows 95/Windows 98, click the SHARP AL-1000 Series Setup tab to display the following screen. * Screen on Windows 95 Default All button When pressed, returns the settings which have been selected by each tab to their default state. OK button All driver settings which have been selected by each tab will be saved and the properties will be terminated. Apply button The settings which have been selected by each tab will be saved. * This button is not displayed on the Windows NT 4. 0 Cancel button The settings which have been selected by each tab will be canceled and the properties will be terminated. However, the settings which have been saved will not be canceled. 19 SETTING PRINT CONDITIONS FROM PRINTER DRIVER Windows 3. 1x: 1 2 3 Double-click the Print Manager icon in the Main window of Program Manager. Select Options in the Print Manager and then select Printer Setup. Select SHARP AL-1000 Series in the Installed Printers: and click the Setup button. 2 Printing 4 The properties of the SHARP AL-1000 Series will be displayed. The following items can be set with the printer driver. Paper/Output Copies Paper source Paper size Specifies the number of sets to be printed. Any number from 1 to 99 can be selected. [. . . ] *4: See the section on INSTALLING THE TD CARTRIDGE. *6: See the section on LOADING COPY PAPER. *7: See the section on BYPASS FEED. 27 USING OTHER INSTALLED DRIVERS If you use another GDI printer or a Windows Printing System printer, interference between printers may occur and printing may not be performed properly. To use another GDI printer or a Windows Printing System printer, you must change the port setting of the printer driver using the following procedure. [. . . ]