User manual SHARP AL-1556

[. . . ] MODEL AL-1556 AL-1566 DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. Money Checks Stamps Passports Bonds Stocks Bank drafts Driver's licenses In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". [. . . ] If you are unable to solve the problem, turn off the main switch, unplug the power cord from the outlet, and contact your dealer. Note For problems related to the printer and scanner functions, see the online manual. DISPLAY MESSAGES When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the indicated page. Note Be sure to use only genuine SHARP parts and supplies. Indication Lamp indicator Display BYPASS : ADD PAPER Tray TRAY * : ADD location Blinks PAPER indicator CLOSE PAPER TRAY * CLEAR PAPER JAM SPF/RSPF JAM. CLOSE THE SPF/ RSPF COVER. Error indicator Blinks Cause and remedy Page The indicated paper tray is not attached, is attached incorrectly, or has run out of paper. Remove the misfeed as explained in "MISFEED REMOVAL". Close the cover. 19 80 83 85 The RSPF cover is open. Replace the REPLACE THE TD TD cartridge with a new cartridge. (When the indicator blinks, the machine does not operate. ) When [L1-00] appears, the scan head locking switch is locked. Turn off the power, release the scan head locking switch, and turn the power back on. SYSTEM ERROR The machine will not function. Turn the [XX - XX] REFER power switch off, wait about 10 TO USER GUIDE seconds, and then turn on the switch again. If this does not clear the error, remove the power cord from the outlet, and contact your authorized service representative. 13 8 - 71 TROUBLESHOOTING AND MAINTENANCE Indication Lamp indicator Display Blinks Error indicator REPLACE THE DRUM CARTRIDGE. Cause and remedy The drum cartridge has reached the end of its life. (When the indicator blinks, the machine does not operate. ) Toner is low. Less than 1000 sheets can be printed with the current drum cartridge. Two sided printing or 2 IN 1 copying is selected when the bypass tray is already selected , or the bypass tray is selected when two-sided printing or 2 IN 1 copying is already selected. Press the [TRAY SELECT] key ( ) to select a paper tray. 2 IN 1 copy and margin shift cannot be used in combination. Copy ratio can not be changed in 2 IN 1 copy. This appears if you attempt to change a user program setting while print job is in progress. The TD cartridge is not installed correctly. Press the [MODE SELECT] key to switch to printer mode and follow the instructions in the display. ("XX" indicates paper size) An original remains on the document glass, or the original is too thick to scan. If the message is no cleared when there is no original on the document glass, the underside of the RSPF is dirty. Clean the underside of the RSPF (especially areas where black lines appear. ) Printing is not possible if the paper size setting is different from the size of paper loaded in the tray. [. . . ] 33 - RSPF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 109 MEMO MEMO Required in IEC-950 (EN 60 950) - Europe · The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) -- United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. [. . . ]