User manual SHARP AL-1611/1622

[. . . ] MODEL AL-1611 AL-1622 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED 2 · MAKING COPIES 16 · STATUS INDICATORS 33 · GENERAL INFORMATION 45 AL-1611 AL-1622 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. [. . . ] Take care in removing paper. Fusing unit release lever G G Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. Be careful about unfixed toner on the misfed paper not to soil your hands or clothes. STATUS INDICATORS 4 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. G The misfeed ( ) indicator will go out. Misfeed removal When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. C. Misfeed in the transport area Open the paper guide by pressing down the projection on either side of the guide and remove the misfed paper. The fusing unit is hot. Take care in removing paper. 1 2 If the misfed paper cannot be removed by the previous step but is visible in the paper output area, remove the paper by pulling it into the paper output area. 41 MISFEED REMOVAL 3 Close the side cover by pressing the handle on the cover. G The misfeed ( ) indicator will go out. Misfeed in the paper tray (upper paper tray in AL-1622) Before opening the paper tray, be sure to confirm that there is no misfed paper in the copier. See page 39. STATUS INDICATORS 1 Gently lift and pull out the paper tray and remove the misfed paper. Misfeed removal 2 Close the paper tray. 3 Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover. G The misfeed ( ) indicator will go out. 42 MISFEED REMOVAL Misfeed in the lower paper tray (AL-1622 only) 1 Grasp the handle of the lower side cover and gently open the cover. 2 Remove the misfed paper. G Be careful not to tear the misfed paper during removal. STATUS INDICATORS 3 If the misfed paper is not seen in step 2, gently lift and pull out the lower paper tray and remove the misfed paper. G Be careful not to tear the misfed paper during removal. Misfeed removal 4 Close the paper tray. 5 Close the lower side cover. G The misfeed ( ) indicator will go out. 43 MISFEED REMOVAL Misfeed in the SPF (AL-1622 only) A B C If an original misfeed occurs in the SPF, the copier will stop and the red indicator which indicates an original misfeed will blink. Location A Feeding roller cover 1 Open the feeding roller cover and pull the original gently to the left and out from the document feeder tray. Close the feeding roller cover. STATUS INDICATORS Location B Right side cover 2 If the misfed original cannot be removed in step 1, open the right side cover and remove the misfed original. Close the right side cover. Misfeed removal Location C 3 Roller If the misfed original cannot be removed in steps 1 and 2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed. If the misfed original cannot be easily removed from the exit area, open the front part of the document feeder tray to remove the original. 4 Open and close the document feeder cover to cancel the misfeed location indicator. After misfed originals are removed, a number may appear in the copy quantity display, indicating the number of originals that must be returned to the document feeder tray. Return the originals and press the START key to resume copying. 44 USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. List of user programs This copier has the following user programs. Program No. 1 2 3 4 5 8 9 10 11 12 13 14 15 * AL-1622 only Program name Auto clear time Preheat mode Auto power shut-off timer Stream feeding mode* Auto power shut-off setting Auto paper select mode* Auto tray switching* Auditing mode Account number entry Account number change Account number deletion Number of copies per account Resetting account Description Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made. Sets the time that elapses before the copier enters the preheat mode after any operation is made. Sets the time that elapses before the copier enters the auto power shut-off mode after any operation is made. Enables or disables the stream feeding mode. Enables or disables the auto power shut-off mode. Enables or disables the auto paper selection. Enables or disables the automatic tray switching which occurs when paper in a tray runs out. (This switching cannot switch to the bypass tray. ) Enables or disables the auditing mode, which controls access to copier. Registers accounts for auditing mode. GENERAL INFORMATION Changes account numbers for auditing mode. [. . . ] Fundamental and Applied Toxicology 17, pp. 280-299. The information on this data sheet represents our current data and best opinion as to the proper use in handling of this product under normal conditions. However, all materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we do not guarantee that these are the only hazards which exist. 73 MEMO MEMO CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CLASS 1 LASER PRODUCT LASER KLASSE 1 Laserstrahl USYNLIG LASERSTRÅLING CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. [. . . ]