User manual SHARP AN-LS1OPERATION MANUAL

[. . . ] · All other company or product names are trademarks or registered trademarks of their respective companies. 2 Contents Introduction Outstanding Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Main Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Respective input terminals can be connected to separate devices, but in actual if one of the terminals is being used the other terminal cannot be used. When data is being transmitted using one input terminal, it is not possible to use the other input terminal until communication using the first terminal is completed. This setting is for operation of the input terminal that cannot be used. It is possible to select whether ERR is returned or nothing is returned when a return (CR:0x0d) code is sent to the terminal that cannot be used. advanced>3 When input is busy, return 1 . . . none (ignore busy input) Busy Reply Select[1-2] : 2 Busy Reply : none (ignore busy input) Enter "3" and press the return key. Select and input number 1 or 2 and press the return key. Display Setting content. Input Hold Time Setting (ADVANCED[4]Input Hold Time) The input terminals of AN-LS1OPERATIONOPERATION can be RS-232C (CONTROLLER) and 10BASE-T. Respective input terminals can be connected to separate devices, but while one is in use, the other is put into an unusable state, and it is possible to protect communication content. The minimum requirement for the Input Hold Time is an interval from transmission of data until a response returned from a projector is complete. When a response is not returned from the projector within a set time, it is possible to reliably receive a response by extending the Input Hold Time. Also when the time of protection for one device is too long, there may be cases where the other device cannot establish communication as desired. If general application software outputs data to this Virtual COM port, Sharp COM Redirection Software will transfer the data to AN-LS1OPERATIONOPERATION which is on a network. With this system, control for a projector conventionally carried out via a COM port can be carried out via an Ethernet LAN without changing control software. Computer Application software Sharp COM Redirection Software (Virtual COM) COM port (RS-232C) Ethernet port Ethernet LAN AN-LS1OPERATIONOPERATION Projector This software supports the following Operating Systems: Windows 98, 98SE, Me, 2000 Professional, XP Home Edition, XP Professional Edition. * Operations are confirmed with English versions of those Windows operating systems only. To Users of Sharp Advanced Presentation Software When using this software via the Virtual COM port and/or the RS-232C (PROJECTOR) terminal, the following functions cannot be used: · Presentation Transfer · Capture & Transfer · Quick Transfer Using the Software 25 Installation The Sharp COM Redirection software (Virtual COM Driver software) is installed using the installation program provided on the CD-ROM. This manual uses examples to explain the operations for installing the software under Windows XP. 1 2 Check that this software is suited for your computer. For details, please refer to "About the Sharp COM Redirection Software". (Page 25) Turn on the power of the computer. · When using Windows 2000 or Windows XP as the operating system, please log in with a login name that has the authority of a system administrator. 3 4 5 Quit all running applications. After a short while, "Choose Destination Location" dialog will be displayed. Assign the destination folder for installation and click "Next>". | The installation will start. 26 · Please change the destination only when necessary. (In general, it is not necessary to change the destination folder. ) · If "Cancel" is clicked, "Exit Setup" dialog will be displayed. · If "Yes" is clicked, the Sharp COM Redirection Software Driver is not installed. If you want to install later, run Sharp COM Redirection Software using "Add or Remove Programs". · Click "No" to continue the installation. If no dialog box is displayed after waiting a while: (1) Select "Run" from the "Start" menu. [. . . ] 32 M Modify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 N Network Ping Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 O OK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Appendix P Password (AN-LS1OPERATIONOPERATION) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]