User manual SHARP AN-W9Z(E) MOUNTINGGUIDE

[. . . ] System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5. Parts Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6. What you can do with the Wireless LAN PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. 1 Project Images on a Large Screen via a Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. 2 Exchange Data via a Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When you want to set computers to communicate via Wireless LAN PC cards using the following settings, you can also communicate between the cards as well. Make sure that the all the computers that will be transmitting data and the projectors have been set the same. · Configure an IP address, Subnet mask and Gateway. · Configure to "Peer-to-Peer" as the "Network Type". · Set the each transmission channel to same channel. · Configure the same name for the network name (SS ID or ESS ID). · Configure the same wireless network key or WEP key, when using "Encryption (WEP security)". · When sending data between Wireless LAN PC cards, make sure to set channel 5 or over as interference may occur if another Wireless LAN PC cards is used nearby. For example, if Wireless LAN PC cards are communicating already on channel 1, then set channel 6. · If no Wireless LAN PC Card is used, you do not have to change the default settings of the transmission channel. · Make sure to consult your Network Administrator should any network related problems occur. The configuration varies depending on your operating system. If your "Link Quality" or "Signal Strength" is "Poor", rescanning can be used to push the transmitter away from a weak Access Point and search for a better link with another Access Point. Shows the short term transmission and reception throughput in bytes/ second, and is continuously updated. The "Link Quality" is displayed as a value and a graph. The "Signal Strength" is displayed as a value and a graph. · Current Tx Rate: · Current Channel: · Rescan: · Throughput: · Link Quality: · Signal Strength: · Disable/Enable Radio: Switches On or Off the Power Save Mode when pressed. When activated, the Power Save Mode reduces the amount of energy consumed. Disable Radio The Power Save Mode is inactive. Enable Radio The Power Save Mode is active. The transmission speed via a wireless LAN is reduced, when the Power Save Mode is enabled. -21 10. 2 "Configuration" Tab In the "Configuration" tab, you can configure the Wireless LAN PC Card. After installing the "Configuration Utility", and after the computer has been started, this dialog box will be displayed. I Setting the Profile Profiles are files that have various settings of the Wireless LAN PC Card. If the settings that you normally use are saved every time as profiles, you can easily modify all at once just by selecting a profile. Click the pull down button on the right of the "Profile Name" box, to see the profiles that can be selected. Selecting and modifying a profile at once 1 2 Click the pull down button on the right of the "Profile Name" box. The profiles that can be selected are displayed. Select the profile from the list and click "Apply". The settings in the profile are modified at once. Right after installation, the profile is only "Default. " Creating a new profile 1 2 3 1 2 3 Change the values for the new profile. [. . . ] 21 PCMCIA connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Rescan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Signal strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]