User manual SHARP AN-WS350R

[. . . ] z Do not apply any other loads to the installation fixtures. Doing so could cause the TV to fall causing injury and damage. z Do not modify or change the installation parts. [. . . ] Do not place the cabinet in a place with poor air circulation, such as in a closet or bookcase. Do not place a drop cloth, etc. , on the installed LCD colour TV. Please strictly observe the following. Special skill is required to install the LCD colour TV and Wall Aside Stand, so please have them installed by a contractor specializing in such installation. The customer should not attempt to install the TV. Sharp shall not be responsible for improper installation or any accidents, damage, or injury resulting from improper installation. E-2 Assembling the Centre Bar and Metal Base Note: Installation of this unit requires 2 or more persons. Step 1 Screw the Support Plate (G) to the Metal Base with 2 pieces of M6 [16mm] screws (K) first, using the M6 Allen key (P). P K G x2 Step 2 Flip the Metal Base upside down. You can see the "SHARP" logo is facing upwards. E-3 Step 3 Place the Centre Bar next to the Metal Base, on top of the Support Plate (G). Side view Ensure that the specification label is facing the floor when combining the Centre Bar and Metal Base. Step 4 From under the Metal Base, place 4 pieces of M8 [50mm] screws (H) with Spring Washers Ø8 (O). The screws should be tightened using Allen key M8 (Q) according to the sequence A B C D as shown above. Step 5 Slowly lift the fixture upwards and let it stand on the floor. E-4 Assembling the Centre Bar and Metal Base (continued) Step 6 Fasten another 4 pieces of M6 [16 mm] screws (K) using M6 Allen key (P) to the Support plate as shown. Step 7 Before peeling off the masking tape securing the legs, hold the legs firmly and be careful not to be hit by them. After peeling off the tape, release the leg slowly until it fully opens out. Be careful not to pinch your fingers in the fixtures. Caution: Specification label Note: When pushing the stand against the wall, the legs will bend inwards. Note: This product is designed to be located against the wall. However, if the user wishes to locate it further away from the wall or at the centre of a room, do ensure that the unit's legs are fully opened. Assembling the LCD Support Frame Step 1 Fix the LCD Support Bar (A) with LCD U Bracket (C) using 4 pieces of M6 [16mm] screws (K) and 4 pieces of Flange Nuts (M). Use M6 Allen key (P) to fasten the screws. E-5 Step 2 Slot in the LCD support frame to the Centre Bar as shown. Step 3 Fix the LCD Support Bar (A) with LCD U Bracket (C) using 4 pieces of M6 [16mm] screws (K) and 4 pieces of Flange Nuts (M). Use M6 Allen key (P) to fasten the screws. Caution: Do not hold the Support Frame at the centre while inserting it to the Centre Bar as this will cause injury. Step 4 Fix the LCD Support Bar (B) using 8 pieces of M6 [16mm] screws (K) and 8 pieces of Flange Nuts (M) as shown. Use M6 Allen key (P) to fasten the screws. Step 5 Screw the Support Frame to the Centre Bar using 6 pieces of M6 [16mm] screws (K). Fasten them with M6 Allen key (P). E-6 Assembling the LCD Support Frame (continued) Notes: z The LCD Support Bar is adjustable to different heights. z When fixing the frame, make sure that all the 6 pieces of M6 [16mm] screws are fastened to it. Caution: z If adjusting to maximum height, make sure that you do not exceed the stopper. z When fixing the frame to maximum height, make sure that all the 6 pieces of M6 [16mm] screws are fastened to it. Stopper Minimum height = 1030 mm E-7 Maximum height = 1250 mm Falling prevention (optional) It is recommended to secure the fixture to the wall with a safety wire or chain before attaching the TV to prevent it from toppling over in case of earthquake occurrence. Screw Fix the safety wire or chain to the wall using a wall anchor bracket which is commercially available. Washer Safety wire (commercially available) Assembling the glass shelf Step 1 Fix the left (S) and right (T) Glass Shelf Supports to the Centre Bar using 4 pieces of M6 [16mm] screws (K) as shown. [. . . ] Fasten them using M6 Allen keys (P) or M8 Allen keys (Q). D U Blu-Ray Compartment x4 x2 N x4 P V For lowerside TV Spacer fixing: turn the spacer guide upwards. x4 E-11 Attaching the LCD TV Hook to the LCD TV (continued) Hook the TV to the LCD Support as shown. Note: LCD colour TVs have a viewing angle (range in which the image can be viewed correctly). The best viewing position is from directly in front of the screen. [. . . ]