User manual SHARP AR-151E

[. . . ] In some areas, the "POWER" switch positions are marked "I" and "0" on the copier instead of "ON" and "OFF". CAUTION: For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. If the AR-151/AR-156 is used without the facsimile expansion kit AR-FX3 then the following directives are applicable : Ha az AR-151/AR-156 készüléket az AR-FX3 képtávíró bõvítõ készlet nélkül használja, akkor az alábbi irányelvek alkalmazandók : Jestlie jsou typy AR-151/AR-156 pouity bez roziøující faxové soupravy AR-FX3, potom budou platit následující smìrnice: Jeli AR-151/AR-156 s¹ u¿ytkowane bez faksowego zestawu rozszerzaj¹cego AR-FX3, nale¿y przestrzegaæ nastêpuj¹cych wskazówek: This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. [. . . ] Place the first original face down on the original table with the TOP toward the LEFT. The first copy can be made using either the paper tray or the manual bypass. B : 60g/m2 copy paper is not recommended for two-sided copying. Replace the first original with the second original face down on the original table with the TOP toward the RIGHT and close the original cover. Make sure that the first and second originals are oriented in the same way on the original table. Both the first and second originals can be set in the SPF / RSPF but they must be set separately. If the stream feeding mode for the SPF / R-SPF has been enabled, set the second original after the SPF / R-SPF ( ) indicator goes out. For tablet binding, turn the first copy over left to right as shown below. For booklet binding, turn the first copy over top to bottom (not shown). Feed the first copy into the manual bypass or into the bypass tray. Be sure to feed the copy paper one sheet at a time. Power save modes (page 1-19) The copier has two power save modes of operation: preheat mode and auto power shut-off mode. Preheat mode When the copier enters the preheat mode, the power ) save indicator will light up and other save ( indicators will remain on or off as before. In this condition, the fuser in the copier is maintained at a lower heat level, thereby saving power. To copy from the preheat mode, make desired copier selections and press the print ( ) key using the normal copying procedure. To exit from the preheat mode, press any key including keys on the operation panel for facsimile or place originals in the SPF (AR-F152). Auto power shut-off mode When the copier enters the auto power shut-off mode, ) indicator will light up and other the power save ( indicators will go out. The auto power shut-off mode saves more power than the preheat mode but requires a longer time before starting copying. To copy from the auto power shut-off mode, press the print ( ) key. Then make desired copier selections and press the print ( ) key using the normal copying procedure. To exit from the auto power shut-off mode, press the print ( ) key or any key onthe operation panel for facsimile or place any originals in the SPF. (When the print ( ) key is pressed one to exit the auto power shut off mode, copying will not start) (AR-F152). [. . . ] Press the clear (>) key to reset the display to zero. Press and hold down the clear (>) key for approximately 5 seconds. The total number of copies will appear in two steps, each with three digits. (normal copying mode) Variable: 50% to 200% in 1% increments (total 151 steps) Fixed: 50%, 70%, 81%, 100%, 141%, 200% Moving optical source, slit exposure (stationary platen) with automatic exposure / SPF or R-SPF : Moving original One paper tray with automatic feed (250 sheets); one single-sheet manual bypass / One bypass tray with 50-sheet automatic feed capability Heat rollers Magnetic brush development Xenon lamp Scan : 400 dpi Output: 600 dpi Scan : 256 levels Output: 2 levels 4MB (AR-121E) / 6 MB (for other models) Local voltage ±10% (For this copiers power supply requirements, see the name plate located on the back of the unit. [. . . ]