User manual SHARP AR-153EN

[. . . ] MODEL AR-153E AR-157E DIGITAL LASER COPIER/PRINTER OPERATION MANUAL Page INTRODUCTION LOADING PAPER MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT OPTIONAL EQUIPMENT INSTALLING THE SOFTWARE APPENDIX 4 7 12 20 25 30 38 40 69 AR-153E AR-157E FOR YOUR RECORDS . . . To protect against loss theft, record and retain for reference the copier's serial number located on the back of the unit. Model Number Serial Number Date of Purchase Authorized Sharp Copier Service Department Number CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using Follow the cautions below when using this unit. Warning: · The fusing area is hot. Exercise care in this area when removing misfed paper. · Do not look directly at the light source. · Do not switch the unit rapidly on and off. [. . . ] When the "Now connect the MFP interface cable to the PC. This will finalize the drivers installation and settings. " dialog box appears, click the "OK" button. After the installation, a message to restart your computer may be displayed. In this case, click the "Yes" button to restart your computer. 10 11 Connect the USB interface cable. (p. 67) Windows will detect the MFP and the Plug and Play screen will appear. Follow the instructions in the Plug and Play screen that appears in your version of Windows to begin the installation. You have completed the installation of the software. 8 49 Installing onto Windows 95/98/Me/NT4. 0/2000 (Parallel interface) Before starting the installation, make sure the USB or parallel interface cable is not connected to the MFP. 1 2 Insert the supplied CD-ROM into your CD-ROM drive. Double-click "My Computer" ( CD-ROM ( ) icon. ), and then double-click the When any of "Hardware Found", or "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button. 3 Double-click the "setup" ( ) icon. If the language selection screen appears after you double click the "setup" icon, select the language you wish to use and click the "Next" button. (Normally, the correct language is selected automatically. ) 4 Select the software packages to be installed, and then click the "Next" button. The software packages with checkmark ( ) on the list on the screen will be installed. Click the "Display README" button to show the information on the selected package. In Windows 95/NT 4. 0, "Button Manager" does not appear. In Windows 98/Me/2000, do not select the "Button Manager" checkbox. because this is not supported when using the parallel interface. 5 The next screen appears. Make sure that the parallel interface cable is not connected, and click "OK". Windows 95/NT 4. 0 Windows 98/Me/2000 6 Check the contents of the package on the screen, and then click the "Start" button. The software packages to be installed will be displayed on the screen. If inappropriate packages are displayed, click the "Back" button to select only appropriate software packages. 50 7 Copying files for MFP driver installation and parallel interface setup (This step will start if it was selected in step 4). 1 2 3 4 After confirming the message in the "Welcome" window, click the "Next" button. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button. Click the "Next" button in the dialog box to install the MFP driver or Cancel to quit the installation. The setup program will start to copy the files. In Windows 2000, if the following screen appears while the files are being copied (the message may appear more than once), click "Yes" in Windows 2000. Click the "Yes" button, and then the Model screen will appear. Select the model number that is the same as the model name of your MFP and click the "Next" button. Be sure to select the displayed model number that is the same as the MFP's model name. If they are not the same, the driver will not be installed correctly. 5 Establish the printer settings and click the "Next" button. [. . . ] This product is not a hazardous material. Reactivity = 0 NFPA Rating (U. S. A. ): WHMIS Legislation (Canada): Transport Information: UN No. : Section 11. Other Information References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-149-261 H. Mermelstein (1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats. [. . . ]