User manual SHARP AR-161 SECTION 1

[. . . ] MODEL AR-160 AR-161 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT · APPENDIX 2 13 27 36 53 69 CAUTIONS Follow the cautions below when using this copier. q q The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. q q q Place the copier on a firm, level surface. [. . . ] To remove it, simply lift the platen cover straight up. q To reattach the platen cover, reverse the above procedure. 15 REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector (, ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. MAKING COPIES Reduction/enlargement/zoom Automatic 1 Place the original on the original table and close the platen cover. 2 3 4 Press the ORIGINAL SIZE ENTER key until the indicator for the size of the original on the original table lights up. Use the TRAY SELECT key to select the paper tray with the desired paper size. q This feature will not work when copy paper of non-standard size is used or the bypass tray is used. Press the AUTO IMAGE key. q q The copy ratio will be automatically set. If the size and orientation of the original do not correspond to standard reduction/enlargement ratios for the selected paper tray, then the ORIGINAL SIZE indicator will blink. However, if an optional electronic sorting kit is installed, the original image may be automatically rotated. If a PRESET RATIO indicator is blinking, part of the original image may not be copied. q 5 6 16 Enter the number of copies. Press the START key. q To cancel the automatic reduction/enlargement mode, press the AUTO IMAGE key again. When copying from an optional SPF with this feature, the automatic reduction/enlargement mode will be automatically cancelled after copying is complete. q REDUCTION/ENLARGEMENT/ZOOM Manual 1 2 A. C. Place the original on the original table and close the platen cover. MAKING COPIES Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. To select a preset reduction or enlargement copy ratio, press the or key repeatedly until the indicator for the desired copy ratio is lit. Preset reduction ratios are: 86%, 81%, 70%, and 50%. Preset enlargement ratios are: 115%, 122%, 141%, and 200%. Zoom ratios: Any ratio from 50% to 200% can be set, in 1% increments. Press the or key to set the approximate ratio, then press the key to decrease the ratio or the key to increase the ratio. q q Reduction/enlargement/zoom When a zoom ( , ) key is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the copy quantity display for at least two seconds. To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display ( ) key. When the key is released, the display will return to the copy quantity display. q D. To decrease or increase the zoom ratio rapidly, press and hold down the or key. However the value will stop at the preset reduction or enlargement ratios. To move beyond these ratios, release the key and then press and hold it down again. Same-size reset: Press the or key repeatedly until the copy ratio returns to 100%. q 3 Ensure that copy paper of the desired size is installed in the paper tray. q If an optional paper feed unit is installed: Use the ORIGINAL SIZE ENTER key to select the original size. Copy paper of the appropriate paper size will be automatically selected depending on the original size and copy ratio. If the selected PRESET RATIO indicator or the ZOOM indicator blinks, the selected copy image is too large for the copy paper size. The desired paper tray can also be selected by pressing the TRAY SELECT key. 4 Set the number of copies and press the START key. 17 BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. [. . . ] For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 39 for setting programs 10 to 15. q 37 USER PROGRAMS 4 Select the desired parameter using the numeric keys. q The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. q Parameters 0 e OFF 1 e 30 sec. [. . . ]