User manual SHARP AR-215

[. . . ] MODEL AR-215 DIGITAL LASER COPIER/PRINTER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS 1 · SPECIAL FUNCTIONS 2 5 23 41 55 · COPIER TROUBLE?67 · GENERAL INFORMATION 79 · OPTIONAL EQUIPMENT 93 · KEY OPERATOR'S GUIDE 119 In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. [. . . ] Job is canceled. <>: paper tray number <>: paper size to be set 68 MISFEED REMOVAL When a misfeed occurs, the copier will stop and the display colour will change from green to orange. The message "Clear paper path. " will appear in the display along with an illustration showing paper misfeed locations. q If paper becomes accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. q For misfeeds in optional equipment, see their respective sections of the operation manual. 5KEY OPERATOR Changing of the display colour can be disabled via a key operator program. See page 136. First confirm the misfeed locations. (p. 75) (p. 73) (p. 69, 70, 74) (p. 74) Misfeed in the bypass tray 1 Gently pull the misfed paper out from the bypass tray. 5 COPIER TROUBLE? 2 Open and close the side cover to cancel the misfeed display. q You q Confirm can also cancel the misfeed display by opening and closing the front cover. that the misfeed display has been cleared. If the misfeed display is not cleared, remove the misfed paper referring to "A. Misfeed in the paper feed area". 69 MISFEED REMOVAL Misfeed in the copier Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to "B. Misfeed in the fusing area". If the misfed paper is seen from this side, proceed to "C. Misfeed in the transport area". If paper is misfed here, proceed to "A. Misfeed in the paper feed area". A. Misfeed in the paper feed area 1 Open the bypass tray and the side cover. 2 Gently open the front cover. COPIER TROUBLE? 70 MISFEED REMOVAL 3 Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it. Roller rotating knob WARNING: The fusing unit is hot. CAUTION: Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. 4 Close the front cover and the side cover. q Confirm that the misfeed display has been cleared. B. Misfeed in the fusing area 1 Open the bypass tray and the side cover. 5 COPIER TROUBLE? 2 Gently open the front cover. 71 MISFEED REMOVAL 3 Turn the roller rotating knob in the direction of the arrow. Roller rotating knob 4 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. After removal, return the release levers to their operating positions. Fusing unit release levers WARNING: The fusing unit is hot. CAUTION: not touch the photoconductive drum (green portion) when removing the misfed paper. [. . . ] Enter another number. " will appear. 5. To change other account numbers, repeat steps 2 to 4. Press the BACK key repeatedly to exit the program. NOTES: q When entering an account number, be sure to input five digits. If not, the OK key will not be accepted. q If you press the CLEAR (C) key when entering an account number, the account number display will change to "-----". KEY OPERATOR'S GUIDE Account Number Security This program is used to make it difficult for users to gain access to accounts by entering code numbers through trial and error. [. . . ]