User manual SHARP AR-235

[. . . ] MODEL AR-235 AR-275 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS · COPIER TROUBLE?· GENERAL INFORMATION · OPTIONAL EQUIPMENT 5 23 41 65 77 91 FOR YOUR RECORDS . . . To protect against loss or theft, record and retain for reference the copier's serial number located on the back of the unit. Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number OUTLINE OF THIS MANUAL 1. GETTING STARTED This chapter describes the basic information on the use of this copier. 1 2 3 4 5 6 2. MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction or enlargement, and exposure adjustments. 3. SPECIAL FUNCTIONS This chapter describes special copying functions including various image editing functions. 4. COPIER TROUBLE? This chapter describes how to remove misfed paper and how to remedy minor problems. 5. GENERAL INFORMATION This chapter describes general information about the use of the copier and the loading of paper and toner. 6. OPTIONAL EQUIPMENT This chapter describes operating instructions for the Single Pass Feeder (AR-SP4), the Reversing Single Pass Feeder (AR-RP3), the Finisher (AR-FN5), the 500-Sheet Paper Feed Unit (AR-D11), and the 2 x 500-Sheet Paper Feed Unit (AR-D12). 1 CONTENTS Page CHAPTER 1 GETTING STARTED INTRODUCTION . 16 G Dehumidification heater switch (DH POWER) . [. . . ] If a program number containing a job program is entered, the message "Storage number selected is already used. Replace it?" will appear to confirm the selection. To replace an existing program with the new program, select "YES" with the and keys and press the OK key. G If the existing program is not to be replaced, select "NO" with the and keys, press the OK key, and select another register number. Deleting a job program SPECIAL FUNCTIONS 1 Press the PROGRAM key. G The JOB PROGRAMS screen will appear. JOB PROGRAMS RECALL STORE DELETE 2 Use the G The and keys to select "DELETE" and press the OK key. DELETE JOB PROGRAM screen will appear. DELETE JOB PROGRAM 1 2 3 4 5 6 7 8 9 [10-key]:SELECT G To cancel the job memory mode, press the BACK key or the CLEAR ALL key. 62 JOB MEMORY 3 Select a program number from 1 to 9 using the numeric keys. G The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the message "Delete job program?" will appear to confirm the selection to delete the program. To delete the program, select "YES" with the and keys and press the OK key. G If "NO" is selected, the previous screen will reappear. Recalling a job program 1 Press the PROGRAM key. G The 3 SPECIAL FUNCTIONS JOB PROGRAMS screen will appear with RECALL highlighted. JOB PROGRAMS RECALL STORE DELETE 2 Press the OK key. G The RECALL JOB PROGRAM screen will appear. RECALL JOB PROGRAM 1 2 3 4 5 6 7 8 9 [10-key]:SELECT 63 JOB MEMORY 3 Select a program number from 1 to 9 using the numeric keys. G The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the settings for that job program will be recalled and the display will return to the basic screen. G The recalled settings may be modified for a particular job run, but any changes made will not be stored in the job memory. To store the new settings, follow the "Storing a job program" procedure. SPECIAL FUNCTIONS 64 CHAPTER 4 COPIER TROUBLE? This chapter describes how to remove misfed paper and how to remedy minor problems. 75 G STATUS 4 65 STATUS MESSAGES If any of the following messages appears in the display, carry out the prescribed remedy. Message (Maintenance icon) Maintenance required soon. Remedy Service by an authorized SHARP service technician will be required soon. Contact your service center as soon as possible. (This message will be displayed if the information key is pressed when the information ( ) icon is displayed. ) Normal maintenance service by an authorized SHARP service technician is needed. A malfunction has occurred which cannot be corrected by the key operator. Contact your authorized SHARP service center for service. Replacement of the toner cartridge will be needed soon. (This message will be displayed if the information key is pressed when the information ( ) icon is displayed. ) See page 82. (Toner cartridge replacement required icon) Toner is low. Check to see if the toner cartridge has been installed properly. Please check paper in paper tray<>. The number of copies on the center tray has reached the limit. Check to see if copy paper has been loaded properly. Load <> paper into The paper size specified for the tray is different from the actual tray <>. [. . . ] Moreover, a two-year cancer bioassay using a typical toner preparation containing carbon black demonstrated no association between toner exposure and tumor development in rats. : In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m3) exposure group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle (4mg/m3) exposure group, but no pulmonary change was reported in the lowest (1mg/m3) exposure group, the most relevant level to potential human exposures. Chronic Effect 12. ECOLOGICAL INFORMATION No data are available. 13. DISPOSAL CONSIDERATION Waste from residues : Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations. [. . . ]