User manual SHARP AR-285 SECTION 3

[. . . ] CHAPTER 8 KEY OPERATOR'S GUIDE This chapter contains information on all of the programs used by the key operator. The programs allow the key operator to tailor many functions of the AR-280/AR-285/AR-335 for specific modes of operation. These programs can only be accessed after a key operator code number has been entered. Please familiarise yourself with this chapter and refer to it for the information you need to keep the copier operating smoothly. q q q q Page KEY OPERATOR CODE NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To cancel an extra preset ratio, select the copy ratio and press the CLEAR ( C ) key. q q 3. Press the "OK" key. Setting a Maximum Number of Copies Use this program to limit the maximum number of copies per copy run which can be input in the copy quantity display. When the "SETTING A MAXIMUM NUMBER OF COPIES. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS SETTING A MAXIMUM NUMBER OF COPIES. MAXIMUM NUMBER OF COPIES KEY OPERATOR'S GUIDE Key operator programs OK 999 (1~999) 1. Input the number using the 10-key pad. CHAPTER8 q A number from 1 to 999 can be set. 2. Press the "OK" key. 8-15 KEY OPERATOR PROGRAMS Initial Margin Shift Setting Set the initial margin shift value with this program. When the "INITIAL MARGIN SHIFT SETTING. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS INITIAL MARGIN SHIFT CANCEL SETTING. SIDE 1 (0~20) mm OK SIDE 2 (0~20) mm 10 10 1. Adjust the value for each side using the keys. q and The value can be set from 0 mm to 20 mm in 1 mm increments (0" to 1" in 1/8" increments). If an optional duplex module (AR-DU1) is not installed in the AR280, the value for the reverse side (side 2) is not displayed. q 2. Press the "OK" key. Erase Width Adjustment Set the initial setting of the amount of the erase area with this program. When the "ERASE WIDTH ADJUSTMENT. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS ERASE WIDTH ADJUSTMENT. EDGE ERASE (0~20) mm OK CENTRE ERASE (0~20) mm 10 10 1. KEY OPERATOR'S GUIDE Key operator programs Adjust the values for the edge erase mode and centre erase mode using the and keys. q The values can be set from 0 mm to 20 mm in 1 mm increments (0" to 1" in 1/8" increments). 2. Press the "OK" key. CHAPTER8 8-16 KEY OPERATOR PROGRAMS Initial Status Setting The copier will assume the initial settings when it is turned on, when the CLEAR ALL ( CA ) key is pressed, or when the auto clear interval has elapsed after a copy run. Use this program to establish the initial settings. When the "INITIAL STATUS SETTING. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS INITIAL STATUS SETTING. 1/4 1/4 RETURN TO THE FACTORY DEFAULT SETTINGS. OK To establish new initial settings 1. Press the "ESTABLISH NEW INITIAL SETTINGS. " key. Select all initial settings on the operation panel. q The following functions cannot be set: Number of copies, XY zoom, automatic copy ratio selection, interrupt, special functions, information, stapling position (for an optional finisher (AR-FN1)) and LCD contrast. 3. Press the "OK" key. To return to the factory default settings Press the "RETURN TO THE FACTORY DEFAULT SETTINGS. " key. Stream Feeding Mode This program is used to enable the stream feeding mode of the document feeder. When the stream feeding mode is enabled, additional originals which are set in the document feeder tray within 5 seconds after the previous original was fed will be fed and copied automatically. KEY OPERATOR'S GUIDE Key operator programs To enable the stream feeding mode, press the check box of "STREAM FEEDING MODE. " to display a check mark in the check box. To disable this mode, press the check box of this program again to clear the check mark in the check box. q The stream feeding mode will only function when the group mode has been selected. CHAPTER8 8-17 KEY OPERATOR PROGRAMS Staple Position Setting This program is used to select the initial stapling position for an optional finisher (AR-FN1). When the "STAPLE POSITION SETTING. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS STAPLE POSITION SETTING. OK 1. 2. Select the desired stapling position on the touch panel. Press the "OK" key. Date Format Setting This program is used to set the initial date format for the date function. When the "DATE FORMAT SETTING. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS DATE FORMAT SETTING. OK 23 April, 1998 April 23, 1998 23/04/98 04/23/98 1. Select the desired date format on the touch panel. q The date formats displayed on the touch panel may be different from the illustration above depending on the country or region. 2. Press the "OK" key. KEY OPERATOR'S GUIDE Key operator programs CHAPTER8 8-18 KEY OPERATOR PROGRAMS Date and Time Adjustment This program is used to adjust the date and time which will be used for printing date. When the "DATE AND TIME ADJUSTMENT. " key is pressed, the following display will appear. KEY OPERATOR PROGRAMS DATE AND TIME ADJUSTMENT. YEAR MONTH DAY HOUR OK MINUTE 1998 10 12 00 (00~23) 00 1. Select an item to be adjusted and adjust the value using and keys. [. . . ] Contact your authorised Sharp Service Centre for service. Use key operator program "DISABLING OF DOCUMENT FEEDER" (page 8-24) to prevent the use of the document feeder. Contact your authorised Sharp Service Centre for service. Contact your authorised Sharp Service Centre for service. THE FINISHER IS OUT OF SERVICE. [. . . ]