User manual SHARP AR-407 OPERATION MANUAL

[. . . ] MODEL AR-287 AR-337 AR-407 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES · COPIER TROUBLE?· GENERAL INFORMATION · OPTIONAL EQUIPMENT · KEY OPERATOR'S GUIDE 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 AR-287/AR-337 AR-407 Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. [. . . ] Check the message on the sub machine and clear the error. If the message "THE SYSTEM IS NOT CONFIGURED TO PERFORM TANDEM JOB. CODE: XX" appears on the main machine, refer to the tandem copy related descriptions in the TROUBLESHOOTING (see page 5-13). To cancel a copy run after starting, press the CLEAR ALL ( CA ) key on the main copier. To cancel the TANDEM copying, press the "TANDEM COPY" key again on the SPECIAL MODES screen of the main copier. q C q q q 3-45 SETTING REVIEW The current settings of copier functions can be displayed on the touch panel. CHAPTER3 SPECIAL FUNCTIONS Setting review 1 100% COPY RATIO Press the REVIEW ( q ) key. The REVIEW screen will appear. The settings of the duplex mode (1-sided to 1-sided, etc. ), sort/ group mode, and special functions will be displayed. The exposure, paper size, and copy ratio which are displayed on the basic screen will not be displayed on the REVIEW screen. Example REVIEW 1-SIDED COPIES OF 1-SIDED ORIGINALS STAPLE SORT MARGIN SHIFT :SIDE 1 mm SIDE 2 mm 10 10 2inl MULTI SHOT :NO BORDER SELECT STAMP :Confidential 1ST PAGE ONLY EXIT 1/2 IDED COPIES OF 1-SIDED GINALS PLE SORT HIFT :SIDE 1 mm SIDE 2 mm 10 10 2inl OT :NO BORDER TAMP :Confidential 1ST PAGE ONLY 2 1/2 To review all setting information, it may be necessary to scroll between review screens. To scroll between screens, use the or key. EXIT ED COPIES OF 1-SIDED NALS E SORT FT :SIDE 1 mm SIDE 2 mm 10 10 2inl :NO BORDER MP Confidential 3 To exit the review screen, press the "EXIT" key. q The basic screen will appear again. 1/2 3-46 CHAPTER 4 SUPPLIES This chapter describes the supplies for this copier such as paper and toner. q q q q PAPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . . . . Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADDING TONER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USED TONER DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . STORAGE OF SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4-2 4-2 4-2 4-5 4-7 4-8 CHAPTER4 4-1 PAPER Types and sizes of copy paper Size Weight Capacity (80 g/m2 (21lb. ) paper) 500 sheets Special paper Paper trays 1 and 2 Bypass tray A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") A6 to A3 (5-1/2" x 8-1/2" to 11" x 17") 56 to 105 g/m2 (15 lbs. to 34 lbs. )* (Ordinary paper) 50 sheets Transparency film, labels, tracing paper, 176 g/m2 (65 lb. paper)** For best results, use only paper recommended by SHARP. * For paper weighing from 105 to 128 g/m2 (28 to 34 lbs. ), A4 (8-1/2" x 11") is the maximum size that can be fed through the bypass tray. ** Paper heavier than 128 g/m2 (34 lbs. ) must be fed narrow side into the feed slot of the bypass tray. q CHAPTER4 SUPPLIES Paper Loading copy paper "OPEN TRAY AND ADD PAPER. " will be displayed when there is no copy paper in a selected paper feed station. When a selected paper tray is not installed or is improperly installed, "PUSH PAPER TRAY INTO THE MACHINE UNTIL IT LATCHES. " will be displayed. Install it or push it back firmly into place. For best results, use only Sharp recommended paper. 4-2 PAPER Loading paper in paper trays 1 and 2 1 Gently lift and pull out the paper tray. CHAPTER4 2 Only use paper within the Sharp specification and follow the paper manufacturer's instructions regarding fanning and loading the paper. SUPPLIES Paper q Maximum height line The tray holds 500 sheets of paper. Do not load paper above the maximum height line. 3 Push the paper tray firmly back into the copier. 4-3 PAPER Changing the copy paper size in the tray 1 Gently lift and pull out the paper tray until it stops. 2 CHAPTER4 8 x13 Adjust the paper size indicator to match the paper size to be set. q Slide the paper size indicator to the right or left to match the paper size. Paper size indicator 3 Left guide Adjust the front guide and left guide while squeezing their lock levers. q B5 4-4 8 x11 216x330 A4 SUPPLIES Paper Slide the front and left guides to match the width and length of the copy paper. Front guide Maximum height line 4 Load copy paper into the tray. B5 5 Paper size card Place the paper size card in the front of the paper tray. q A3 The paper size card has three faces. [. . . ] Contact your authorised Sharp Service Centre for service. Use key operator program "DISABLING OF DOCUMENT FEEDER" (page 8-25) to prevent the use of the document feeder. Contact your authorised Sharp Service Centre for service. Contact your authorised Sharp Service Centre for service. THE FINISHER IS OUT OF SERVICE. [. . . ]