User manual SHARP AR-507

[. . . ] MODEL AR-507 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES · COPIER TROUBLE?· GENERAL INFORMATION · OPTIONAL EQUIPMENT · KEY OPERATOR'S GUIDE 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. [. . . ] The page number print position is automatically selected depending on the selected page number format. If reduction or enlargement is used with this function, the print position may move or the page numbers may not be printed. CHAPTER3 q -1- 1/5 1 SPECIAL FUNCTIONS Text stamp 1 Place the originals in the document feeder tray or on the document glass. READY TO CO 2 Press the SPECIAL MODES key. q The SPECIAL MODES screen will appear. READY TO COPY. SPECIAL MODES MARGIN SHIFT MULTI SHOT PAMPHLET COPY AUTO EXPOSURE ERASE COVERS IMAGE EDIT AUTO A4 PAPER SELECT OK DUAL PAGE COPY TRANSPARENCY INSERTS TEXT STAMP 100% COPY RATIO 3 Press the "TEXT STAMP" key on the touch panel. q The TEXT STAMP menu will appear. 3-41 TEXT STAMP PECIAL MODES EXT STAMP DATE WATERMARK PRINT DIRECTION CHAPTER3 SPECIAL FUNCTIONS Text stamp OK OK SELECT STAMP PAGE NUMBER 4 Press the "PAGE NUMBER" key on the touch panel. q The setting screen for PAGE NUMBER will appear. READY TO COPY. OK FIRST PAGE NUMBER 1 (0~) OK GE NUMBER CANCEL -1-, -2-, -3-. . OK FIRST PAGE NUMBER 1 5 6 Select the desired page number format. q The selected page number format will be highlighted. OK CANCEL -1-, -2-, -3-. . OK FIRST PAGE NUMBER 1 (0~) Select the starting page number. q Use the number. or key to increment or decrement the page q If the page number format "1/5, 2/5, 3/5. . " has been selected in step 5, the starting page number is fixed to 1 and cannot be changed. OK CANCEL -1-, -2-, -3-. . OK FIRST PAGE NUMBER 1 (0~) 7 Press the lower "OK" key. q The TEXT STAMP menu will appear again. DATE WATERMARK PRINT DIRECTION SELECT STAMP PAGE NUMBER 8 Select the print direction. q If the PAMPHLET COPY function is used with this function, the portrait orientation ( ) must be selected. 3-42 TEXT STAMP OK EXT STAMP DATE WATERMARK PRINT DIRECTION SELECT STAMP PAGE NUMBER OK 9 Press the upper "OK" key. CHAPTER3 1 4 7 AUDIT CLEAR 2 5 8 0 3 6 INT CLEAR ALL CA START 9 PROGRAM 10 11 12 Make all other desired copier selections and enter the desired number of copies. Press the START ( q ) key. SPECIAL FUNCTIONS Text stamp If the document feeder is used, copying will start after all originals are scanned. If the document glass is used, proceed to the next step. q P PLACE NEXT ORIGINAL. READ-END AUTO EXPOSURE AUTO A4 PAPER SELECT 100% COPY RATIO Replace the finished original with the next original after the START ( ) key indicator lights up, and then press the START ( ) key. Repeat this step until all originals have been scanned. Then, press the "READ-END" key on the touch panel. q q q Copying will start at this time. Up to 120 sheets of A4 (8-1/2" x 11") originals or up to 60 sheets of originals larger than A4 (8-1/2" x 11") can be scanned. To cancel the PAGE NUMBER function, select the PAGE NUMBER function again and press the "CANCEL" key. 3-43 TANDEM COPY If this copier is connected with another copier of the same model equipped with the same options through the tandem-connection cable (AR-CA1), copying with the two machines can be performed eventually making the total copy time for multiple copies one-half of the case when using a single copier. q A dedicated tandem-connection cable AR-CA1 is required for tandem copying. q The tandem copying can be used only in the sort mode or staple sort mode. q The transparency inserts function cannot be used with this function because the number of copies must be 1 when the transparency inserts function is used. q The TANDEM COPY key will only be displayed on the touch panel of the machine set as the main copier, (an authorised Sharp Service Technician will do the setting of the main and sub copiers at the time of installation). When the tandem function is selected, (only available on the main copier) the other will then become the sub copier. The setting procedure is described below. q CHAPTER3 SPECIAL FUNCTIONS Tandem copy INTERRUPT will not function during tandem copying. 1 2 READY TO CO Ensure that the two copiers are connected through the tandem-connection cable and they have been turned on. On the copier that will be set as the main copier, place the originals in the document feeder tray or on the document glass. 3 Press the SPECIAL MODES key. q The SPECIAL MODES screen will appear. READY TO COPY. [. . . ] Contact your authorised Sharp Service Centre for service. Use key operator program "DISABLING OF DOCUMENT FEEDER" (page 8-27) to prevent the use of the document feeder. Contact your authorised Sharp Service Centre for service. Contact your authorised Sharp Service Centre for service. THE FINISHER IS OUT OF SERVICE. [. . . ]