User manual SHARP AR-5520N START GUIDE

[. . . ] The socket-outlet shall be installed near the equipment and shall be easily accessible. OUTLINE OF THIS MANUAL 1. GETTING STARTED This chapter describes the basic information on the use of this copier. 2 1 2 3 4 5 6 7 8 2. MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction or enlargement, and exposure adjustments. 3. SPECIAL FUNCTIONS 1 This chapter describes special copying functions including various image editing functions. 4. SPECIAL FUNCTIONS 2 This chapter describes the functions that can be used when the optional dual function board (AR-EB4) is installed. 5. COPIER TROUBLE? This chapter describes how to remove misfed paper and how to remedy minor problems. 6. GENERAL INFORMATION This chapter describes general information about the use of the copier and the loading of paper and toner. 7. OPTIONAL EQUIPMENT This chapter describes operating instructions for the Single Pass Feeder (AR-SP4), the Reversing Single Pass Feeder (AR-RP3), the Finisher (AR-FN5 N), the 500-Sheet Paper Feed Unit (ARD11), and the 2 x 500-Sheet Paper Feed Unit (AR-D12). 8. KEY OPERATOR'S GUIDE This chapter contains information about all programs for use by the key operator. The programs allow the key operator to tailor many functions of this copier for specific modes of operation. 1 CONTENTS Page CHAPTER 1 GETTING STARTED INTRODUCTION . 20 CHAPTER 2 MAKING COPIES NORMAL COPYING . [. . . ] For best results, use only SHARP recommended paper. The message "TRAY<>: Add paper. " will be displayed when there is no copy paper in the selected paper feed station. When the selected paper tray is not installed or is improperly installed, "Close paper tray <>. " will be displayed. Install it or push it back firmly into place. NOTE: When the paper size is changed in a paper tray, the size of the paper must be entered as described on page 82. If not, the machine will stop copying and the message "Load <> paper into tray <>. " will appear in the display. In this case, load the paper requested in the message. <> : paper tray number <>: paper size to be set 1 Pull out the paper tray until it stops. GENERAL INFORMATION 2 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. Front guide Left guide 80 PAPER 3 Move the left guide to the appropriate slot as marked on the tray. q When using 11" x 17" copy paper, store the left guide in the slot at the left front of the paper tray. 4 Fan the copy paper and insert it into the tray. Maximum height line q Set the paper along the guides. tray holds up to 500 sheets of 80 g/m2 (21 lb. ) paper. q Do not load paper above the maximum height line. q The 5 Push the paper tray firmly back into the copier. q If the paper size is changed in steps 3 and 4, place the paper size card in the front of the paper tray to indicate the selected paper size. Proceed to the next section. 6 GENERAL INFORMATION 51/2x81/2 A5 B5 R A4 A3 81/2x13 81/2x11 81/2x14 81/2x11R A4 R 81/2x13 Paper size card 11x17 A4 EXTRA EXTRA B4 B5 81/2x11 Paper size card 81 PAPER Changing the copy paper size in the tray Paper size setting can only be done while the machine is not operating and the COPY mode has been selected. A two-sided copy is also counted as two sheets. About the toner indicator The amount of toner remaining is indicated in 5 levels. Use this indicator as a guideline for replacement of the toner cartridge. Refer to the table below for the relation between the indicator level and the amount of toner remaining. q When the toner level falls below 25%, obtain a replacement toner cartridge as soon as possible. q For more information, consult your dealer. Toner level indicator Amount of toner remaining (approximate) 100% to 90% TONER REMAINING(%) 0 25 50 75 100 TONER REMAINING(%) 0 GENERAL INFORMATION q The 90% to 75% 25 50 75 100 75% to 50% TONER REMAINING(%) 0 25 50 75 100 TONER REMAINING(%) 0 25 50 75 100 50% to 25% TONER REMAINING(%) 0 25 50 75 100 Less than 25% Obtain a replacement toner cartridge as soon as possible. NOTE: amount of toner used will vary depending on conditions of machine usage and the content of the documents printed. Use the above toner levels as a general guideline. 86 CLEANING THE PLATEN GLASS AND PLATEN COVER Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Stains or dirt on the platen glass or platen cover will also be copied. Wipe the platen glass and platen cover with a soft, clean cloth. q If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. [. . . ] Eye Protection : None required when used as intended in Sharp equipment. Skin Protection : None required when used as intended in Sharp equipment. Other Protective equipment : Use of a dust mask and goggles are recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Physical State: Solid Ph : Boiling/Melting Point : Flash Point (°C ) : Explosion Properties : : Density (g/cm3) Solubility in water : Form: Powder Not applicable Not applicable Not applicable No data 7. 3 (bulk density : 2. 0) Negligible Color: Black Odor: odorless 151 10. [. . . ]