User manual SHARP AR-620U

[. . . ] For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. The CE mark logo label is affixed on an equipment in case that the directives described in the above sentence are applicable to the product. (This sentence is not applicable in any country where the above directives are not required. ) WARNING: Changes or modification made to this equipment, not expressly approved by Sharp or parties authorised by Sharp, could void the user's authority to operate the equipment. 1 EPA ENERGY STAR ® (MFD) The United States Environmental Protection Agency (EPA) has introduced a voluntary program, the ENERGY STAR Program, to encourage the widespread and voluntary use of energy-efficient technologies that enhance the workplace, improve product performance and prevent pollution. As an ENERGY STAR Partner, the SHARP Corp. [. . . ] Select other copy modes as required. 11 12 Press the START key. 4-29 14. OVERLAY This function stores the images that you frequently use and makes copies by overlaying on to the copied originals. * The stored image cannot be printed with reduction and enlargement. However, the original can be overlaid with reduction and enlargement by adjusting it to the size of stored image. Storing image 1 2 3 Overlay 4 5 6 7 8 9 10 11 12 Storing Image 1 2 Place the original you want to have memorized. Page 2-9 Press the EDIT key to enter the edit menu, and press the OVERLAY key. - If the desired function keys are not displayed, press the Next key to change the menu screen. 3 Press the MEMORIZE key. 4 Press the row of the file name list you desire, then press the FILE NAME key. 4-30 USING THE EDITING FUNCTIONS 5 6 7 Input the file name with the screen for entering letters and press the SET key. - Entering letters Page 5-28 1 2 3 Press the START key. - The original starts scanning to memorize the image. The image will be stored as shown on the right. 4 5 Confirming Stored Image (Test Print) 6 7 8 9 10 11 12 1 2 1 2 3 Perform steps 2 and 3. Page 4-29 Press the file name you desire (the selected file name will be shaded), then press the TEST PRINT key. - The stored image starts printing out. Deleting Image Perform steps 2 to 3. Page 4-29 Press the file name you desire (the selected file name will be shaded), then press the DELETE key. Press the Delete key. 4-31 14. OVERLAY (Cont. ) 1 2 3 4 5 6 7 8 9 10 11 12 Overlaying Originals with Stored Image 1 2 3 4 Place paper in the drawer(s). Place the original(s). Page 2-9 Page 2-4 Press the EDIT key to enter the edit menu, and press the OVERLAY key. - If the desired function keys are not displayed, press the Next key to change the menu screen. Press the OVERLAY key. 5 6 1 2 Press the file name you desire (the selected file name will be shaded) , and press the SET key. Select other copy modes as required. Press the START key. Confirming Overlay (Test Print) When overlaying more than one original with the stored image, the first original is overlaid with the stored image and printed out. Perform the above step 1 to step 4. Press the file name you desire (the selected file name will be shaded), and press the TEST PRINT key. - The overlaid image starts printing out. 4-32 USING THE EDITING FUNCTIONS 15. SHARPNESS ADJUSTMENT This function allows you to emphasize the letters and edges of images. 1 2 1 2 3 Place paper in the drawer(s). Page 2-4 Place the original(s). Page 2-9 Press the EDIT key to enter the edit menu, and press the SHARPNESS key. - If the desired function keys are not displayed, press the Next key to change the menu screen. 3 4 5 4 5 6 Press the SOFT ( or SHARP ) key. - Pressing the SOFT key suppresses the moire fringe key emphasizes the letters while pressing the SHARP and sharpens the fine lines. 6 7 8 9 10 11 12 Press the SET key. Select other copy modes as required. Press the START key. Cancelling the Sharpness Adjustment Press the DEFAULT key, then the SET key. 4-33 16. DIRECTION OF DUPLEX COPY IMAGES (Rotation) 1 2 3 4 5 6 7 8 9 10 11 12 When lengthwise A3, A5, B4 or LD paper is copied under the mode of 1-Sided Originals to 2-Sided Copies, 2-Sided Originals to 1-Sided Copies, this function allows you to adjust the direction for `side-by-side' opening. * This function is not necessary for copying in the direction of `vertical' opening. set non set 1 2 3 4 Place paper in the drawer(s). MIXED-SIZED ORIGINALS When placing the different-sized originals in the reversing automatic document feeder, you can make copies by setting MIXED-SIZED ORIGINALS. The available combination of mixed-sized originals are as follows: - A3, A4, A4-R, B4, B5 - LD, LG, LT, LT-R * The image may be copied out of position depending on the combination. 1 2 3 4 5 6 7 8 9 10 11 1 2 Place paper in the drawer(s). - Bypass copying is not possible. Page 2-4 Adjust the slide to the widest paper size, and align the originals against the left front side. - Place the originals face up. 3 Press the PROGRAM key to enter the programme menu, and press the MIXED ORIGINAL SIZES key. 4 5 Press the SET key. Select either the Automatic Paper Selection ( Page 3-2) or Automatic Magnification Selection mode ( Page 3-4). - To make duplexed copies, select the automatic magnification mode. Select other copy modes as required. 6 12 Press the START key. 5-4 USING THE SPECIAL FUNCTIONS 3. JOB MEMORY You can store and recall a combination of frequently used copy jobs at anytime. Up to four such combinations of job can be stored. * You cannot delete the copy modes that have already been stored in the memory, but you can rewrite new jobs on the memory key in which some copy modes have already been stored. 1 2 Storing a Combination of Copy Job Settings 1 2 Select the desired copy modes. Example : Reproduction ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85% Copy quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 copies Paper size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A4-R 3 4 5 6 Press the PROGRAM key to enter the programme menu, and press the JOB MEMORY key. 3 Press the MEMORY key. 7 8 9 4 Press the desired Memory Number key. - The copy job settings are stored in the selected Memory Number key. 10 11 12 - Memory Number keys where copy jobs have been already stored are shown in a half-tone shaded pattern. - The stored copy jobs remain unchanged until different copy jobs are entered. (They are retained even after the power switch is turned off. ) 5-5 3. [. . . ] 4-23 Setting Tab Paper in the Drawer . . . . . . . . . . . . . . . . . . . 4-22 Setting the "Other" Size Key . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Setting the Automatic Energy save mode . . . . . 5-16 Setting the Automatic Off-Mode . . . . . . . . . . . . . . . . . . . . . [. . . ]