User manual SHARP AR-BC260

[. . . ] The socket-outlet shall be installed near the equipment and shall be easily accessible. To protect against loss or theft, record and retain for reference the machine’s serial number located on the back of the unit. Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier/Printer Service Department Number AR-BC260 Warranty While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice. [. . . ] Even if the message above is displayed, copying can be performed onto the currently selected paper. (*Note) The following requirements must be satisfied. Originals of a standard size (11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R or 5-1/2" x 8-1/2" (A3, B4, A4, A4R, B5, B5R or A5)) are set and the auto paper select function is enabled. If originals of a size other PLAIN than the sizes above are 8½x11 to be copied, manually RECYCLED select the desired paper 8½x14 size by touching the [PAPER SELECT] key 11x17 PLAIN and then touching the desired paper size selection key. The selected key will be highlighted and the paper selection screen will close. To close the paper selection screen without making a selection, touch the [PAPER SELECT] key. 8½x11 DUPLEX 8½x11 11x17 The one-sided to onesided mode is selected when no icon for a twosided mode appears in the dashed area on the display. If the 1-sided to 1-sided copy mode is already selected, steps 3 to 5 are not needed. 3 Touch the [2-SIDED COPY] key. 2-SIDED COPY OUTPUT 4 Touch the [1-sided to 1-sided copy] key. It may happen that a mode other than [1sided to 1-sided copy] is selected, thus [1-sided to 1-sided copy] should be selected again. (Touch the [1-sided to 1sided copy] key so that it is highlighted. ) 5-2 ApollonII_general-copy_SEC. book 3 ページ ２００４年９月６日　月曜日　午後４時５７分 NORMAL COPYING 7 Select the desired output mode (see page 5-5). 2-SIDED COPY OUTPUT The sort mode is the default mode. To select the group mode, touch the [OUTPUT] key, then touch the [GROUP] key on the output setting screen, and then touch the [OK] key on the setting screen. numeric 8 Use the of copies. keys to set the desired number Up to 999 can be set. If you are only making a single copy, the copy can be made with the copy number display showing "0". Use the [C] (clear) key to cancel an entry if a mistake has been made. 9 Press the [COLOR COPY( START ( or [BLACK COPY START )] key. )] If the [C] key is pressed while originals are being scanned, scanning will stop. If the message appears, load paper in a paper 100% tray with paper of the required size. Even if the message above is displayed, copying can be performed onto the currently selected paper. AUTO 8½x11 PAPER SELECT Original size detector 5 [ How to place the original ] Place the original in the appropriate position shown below according to its size. ( Center the original on the centering scale. ) Original scale Centering scale 8½x11 or A4 11x17 or A3 8½x14 or B4 (*Note) The following requirements must be satisfied. Originals of a standard size (11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R or 5-1/2" x 8-1/2" (A3, B4, A4, A4R, B5, B5R or A5)) are set and the auto paper select function is enabled. If originals of a size other PLAIN than the sizes above are 8½x11 to be copied, manually RECYCLED select the desired paper 8½x14 size by touching the [PAPER SELECT] key 11x17 PLAIN and then touching the desired paper size selection key. The selected key will be highlighted and the paper selection screen will close. To close the paper selection screen without making a selection, touch the [PAPER SELECT] key. Original scale Centering scale 8½x11 R or A4 R 5½x8½ or A5 2 Ensure that the 1-sided to 1-sided copy mode is selected. ORIGINAL 8½x11 PLAIN 5½x8½ 8½x11 DUPLEX 8½x11 11x17 The one-sided to onesided mode is selected when no icon for a twosided mode appears in the dashed area on the display. 5-7 ApollonII_general-copy_SEC. book 8 ページ ２００４年９月６日　月曜日　午後４時５７分 NORMAL COPYING 4 Select the desired output mode. (See page 5-5. ) When a document is detected on the 2-SIDED COPY document glass, the group mode will be automatically selected. OUTPUT To select sort copy, touch the [OUTPUT] key, then touch the [SORT] key on the displayed screen, and then touch the [OK] key. NOTE If the [SORT] or [GROUP] key is touched, its corresponding icon will appear on the touch panel. To clear the icon display, press the [CA] (clear all) key. [. . . ] 2-9 to 2-10, 5-17 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 - Duplex bypass/inverter unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 - Duplex module/2 x 500 sheet paper drawer . . . . . 2-8 - Large capacity tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]