User manual SHARP AR-C160

[. . . ] MODEL AR-C160 DIGITAL FULL COLOR COPYING MACHINE OPERATION MANUAL · GETTING STARTED · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES · COPIER TROUBLE?· GENERAL INFORMATION · OPTIONAL EQUIPMENT Page 1-1 2-1 3-1 4-1 5-1 6-1 7-1 Digital lllllllllllllllll llllllllllllllllllllllllllllllllllllllllllllllll l lllllllllllllllll The power switch positions are marked "I" to indicate power "ON" and " " to indicate stand-by. In the stand-by position, power is being supplied to a drying heater within the optical system of the copier. Caution: For complete electrical disconnection, pull out the main plug. [. . . ] When the COVERS mode is selected, the stream feeding mode of the RADF will always be off. CHAPTER3 SPECIAL FUNCTIONS Covers 2-SIDED COPY OUTPUT 1 Place the originals in the optional document feeder tray. 2 AUTO SPECIAL MODES Press the 2-SIDED COPY key and select the desired duplex mode if needed. Press the "OK" key to close the duplex selection window. q To copy in the 1-sided to 2-sided or 2-sided to 2-sided copy mode, an optional duplex module (AR-DU2N) must be installed. READY TO 3 4 Press the SPECIAL MODES key. q The SPECIAL MODES screen will appear. 2-SIDED COPY Press the "COVERS" key on the touch panel. q The setting screen for COVERS will appear. READY TO COPY. SPECIAL MODES MARGIN SHIFT CENTERING COVERS AUTO EXPOSURE ERASE LOAD COVER STOCK INTO BYPASS-TRAY. OK DUAL PAGE COPY OK COVERS FRONT BACK FRONT+BACK CANCEL OK PRINT ON FRONT COVER?YES NO TRANSPARENCY INSERTS COLOR ADJUSTMENTS 1 AUTO 8/2 11 PAPER SELECT IMAGE EDIT 100% COPY RATIO 3-14 COVERS O COVERS FRONT BACK FRONT+BACK CANCEL O PRINT ON FRONT YES NO 5 Select cover placement. q Select "FRONT", "BACK" or "FRONT+BACK" on the touch panel. CHAPTER3 OK CANCEL OK PRINT ON FRONT COVER?T YES NO T+BACK 6 Indicate whether the front cover sheets are copied on or not. q Select "YES" or "NO" on the touch panel. If "YES" is selected, the first page of the document will be copied onto the front cover sheet. If "BACK" has been selected in step 5, this selection is not needed. SPECIAL FUNCTIONS Covers q OK NCEL OK T ON FRONT COVER? CUS SETT 7 Press the upper "OK" key. 8 Load the cover stock into the bypass tray, making sure that the cover stock is the same size as the copy paper. q The message "SELECT PAPER TYPE FOR BYPASS-TRAY. " will appear if "16 ~ 28 lbs. " ("PLAIN PAPER"), "28+ ~ 35 lbs. " ("HEAVY PAPER 1") or "35+ ~ 75 lbs. " ("HEAVY PAPER 2") has not been selected. 9 1 4 7 AUDIT Select the paper type for the bypass tray. q q Transparency film cannot be selected as cover stock. The START key indicators will light up. 2 5 8 0 3INTERRUPT 6 INTE CLEAR CLE CA AL ALL 9 PROGRAM CC 10 Enter the desired number of copies and press the COLOR COPY START ( ) key or BLACK COPY START ( ) key. q P CLEAR CL To cancel the COVERS function, select the COVERS function again and press the "CANCEL" key. 3-15 COLOR ADJUSTMENTS The color adjustments include the following items. q RGB adjust: Strengthens or weakens one of three primary colors, red (R), green (G), or blue (B). q Sharpness: Sharpens or softens image outlines. q Suppress background: Suppresses copying of lighter background areas. q Color balance: Adjusts the color, tone, and density of color copies. q Brightness/intensity/contrast: These adjust the level of brightness, intensity or contrast of images. RGB ADJUST This function can be used to strengthen or weaken the three primary colors, red (R), green (G), or blue (B). Only one primary color can be adjusted at a time. If a second primary color is adjusted, the first adjustment will be cancelled. (Refer to the samples on page 5 to see the effect on copy images in relation to the RGB ADJUST. ) CHAPTER3 SPECIAL FUNCTIONS Color adjustments 1 Place the original on the document glass or in the optional document feeder tray. SPECIAL MODES READY TO 2 3 Press the SPECIAL MODES key. q The SPECIAL MODES screen will appear. 2-SIDED COPY Press the "COLOR ADJUSTMENTS" key on the touch panel. q The COLOR ADJUSTMENTS menu will appear. READY TO COPY. READY TO COPY. SPECIAL MODES MARGIN SHIFT CENTERING COVERS AUTO EXPOSURE ERASE OK DUAL PAGE COPY SPECIAL MODES COLOR ADJUSTMENTS RGB ADJUST COLOR BALANCE BRIGHTNESS INTENSITY SHARPNESS OK OK TRANSPARENCY INSERTS COLOR ADJUSTMENTS 1 AUTO 8/2 11 PAPER SELECT SUPPRESS BACKGROUND IMAGE EDIT 100% COPY RATIO CONTRAST 3-16 COLOR ADJUSTMENTS READY TO COPY. SPECIAL MODES COLOR ADJUSTMENTS RGB ADJUST COLOR BALANCE BRIGHTNESS INTENSITY CONTRAST SHARPNESS OK OK 4 Press the "RGB ADJUST" key on the touch panel. q The setting screen for RGB ADJUSTMENTS will appear. READY TO COPY. SPECIAL MODES CANCEL RGB ADJUST ONLY ONE COLOR CAN BE ADJUSTED. R(RED) G(GREEN) OK OK B(BLUE) SUPPRESS BACKGROUND CHAPTER3 READY TO COPY. SPECIAL MODES CANCEL RGB ADJUST ONLY ONE COLOR CAN BE ADJUSTED. R(RED) G(GREEN) OK OK B(BLUE) -2 · -1 · · 0 · · 1 · 2 5 6 Select a color to be adjusted. SPECIAL FUNCTIONS Color adjustments q Select a color from R (RED), G (GREEN), and B (BLUE). -2 · -1 · · 0 · · 1 · 2 CANCEL RGB ADJUST ONLY ONE COLOR CAN BE ADJUSTED. [. . . ] Check that the cartridge locks in place by pulling it slightly. The cartridge holds 3, 000 staples. q NOTE: Be sure to remove the rear paper and tape before inserting the cartridge. 7-22 FINISHER (AR-FN4) 5 Remove the rear paper and tape from the cartridge. q Pull them straight. If they are pulled obliquely, the tape may be torn. 6 Insert the staple box into the stapler until it clicks in place. 7 Push the finisher toward the copier and latch it in place. q If the stapler does not work properly after cartridge installation, it may have a jammed staple in it. Staples for the finisher are available from your Sharp dealer. q CAUTION Use caution while latching the finisher into place. OPTIONAL EQUIPMENT Finisher (AR-FN4) To prevent pinching your fingers, do not place your hand or fingers on the release lever while moving the finisher toward the copier. CHAPTER7 7-23 FINISHER (AR-FN4) Staple jam removal If staples become jammed in the stapler, the message "CHECK STAPLER POSITION OR STAPLE JAM" will appear. [. . . ]