User manual SHARP AR-C170M

[. . . ] MODEL AR-C170M DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM OPERATION MANUAL (for general information and copier operation) Page · BEFORE USING THE PRODUCT · MANAGING THE MACHINE · PERIPHERAL DEVICES · BEFORE MAKING COPIES · BASIC PROCEDURE FOR MAKING COPIES · CONVENIENT COPY FUNCTIONS · MACHINE MAINTENANCE (FOR COPYING) · SPECIFICATIONS 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product. Before installing this product, be sure to read the installation requirements and cautions sections. (Option) Duplex bypass / inverter unit and Stand / 3 x 500 sheet paper drawer Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual for general information and copier operation" and operation manuals for any optional equipment which has been installed. In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. If your copier is so marked, please read "I" for "ON" and " " for "OFF". [. . . ] If you are only making a single copy, the copy can be made with the copy number display showing "0". Use the [C] (clear) key to cancel an entry if a mistake has been made. NOTE If colour copies are made with the output set to "Sort", only one set of copies will be made even if a selection is made for a greater number of copies. (See page 5-5 "Copy output (sort and group)"). When "Group" is selected, the selected number of copies will be made (See next page 5-4 "Copy mode output restrictions"). 5 9 Press the [COLOUR COPY( START ( or [BLACK COPY START )] key. )] If the [C] key is pressed while originals are being scanned, scanning will stop. If copying had already started, copying and scanning will stop after the original in progress is output to the original exit area. In these cases the copy quantity will be reset to "0". NOTE The 1-sided to 1-sided copying mode is set as the default in the initial settings. If the default setting has not been changed using the "Initial status settings" program (key operator program), steps 3 to 5 on page 5-2 can be omitted. 5-3 NORMAL COPYING Copy mode output restrictions No added memory Number of copies entered No Yes Two-sided copying mode Output mode original/paper size Sort/ Group Sort Only one copy possible Only one copy possible Only one copy possible Group Memory added (128 MB or 256 MB) Number of copies entered No Yes Sort/ Group Sort Only one copy possible Only one copy possible Only one copy possible Group Up to A4 (8-1/2" x 11") Colour copying One-sided copying B4, A3 (8-1/2" x 14", 11" x 17") A3W (12" x 18")* Up to A4 (8-1/2" x 11") Black and B4, A3 white (8-1/2" x 14", 11" x 17") copying A3W (12" x 18")* Up to A4 (8-1/2" x 11") Colour copying Automatic two-sided copying B4, A3 (8-1/2" x 14", 11" x 17") Only one copy possible Only one copy possible Only one copy possible A3W (12" x 18")* Up to A4 (8-1/2" x 11") Black and B4, A3 white (8-1/2" x 14", 11" x 17") copying A3W (12" x 18")* : Copying possible using selected settings : Copying not possible * A3W (12" x 18")-size paper cannot be used for automatic two-sided copying. A3W (12" x 18") only indicates the paper size. Specifications for memory capacity and maximum number of originals Added memory None 128 MB 256 MB Maximum number of originals 2 2 2 1*2 2 2 1 1 1 400 400 680 200 200 340 165 165 280 Text original (A) : A4 or 8-1/2" x 11" Original size Up to A4 (8-1/2" x 11") Colour B4, A3 (8-1/2" x 14", 11" x 17") copying*1 A3W (12" x 18")*3 Black and Up to A4 (8-1/2" x 11") B4, A3 (8-1/2" x 14", 11" x 17") white copying*4 A3W (12" x 18") Mode *1 For colour copying, the selected number of copies will be printed for each original scanned. (Sorting is not possible. ) *2 In automatic two-sided copy mode, at least 128 MB of added memory is required to copy on B4 and A3 (8-1/2" x 14" and 11" x 17") paper. *3 A3W (12" x 18") paper cannot be used in automatic two-sided copy mode. *4 Sorting is possible when making black and white copies. If the number of originals does not exceed the above indicated limit, all originals are scanned into memory and then the set number of sets of copies is printed. (The number of originals is based on text original (A). ) 5-4 NORMAL COPYING Copy output (sort and group) Example: Making five sets or five copies each of three originals G Sorting copies into sets Original Press the [BLACK COPY START] key OUTPUT SPECIAL MODES SORT Five sets of copies In the case of colour copying, only one set of copies can be made even if a selection is made for the number of copies. (See "Copy mode output restrictions" on page 5-4. ) If multiple sets are needed, place the original on the original table again and repeat the copying procedure for each set needed. 2-SIDED COPY OUTPUT GROUP Set the number of copies (5) Touch the [OUTPUT] key Touch the [SORT] key Press the [COLOUR COPY START] key "Sort" is automatically selected when the original is placed on the document feeder tray of the reversing single pass feeder. G Grouping copies by page Original Press the [BLACK COPY START] key OUTPUT SPECIAL MODES SORT 2-SIDED COPY 5 5 copies per page Press the [COLOUR COPY START] key OUTPUT GROUP Set the number of copies (5) Touch the [OUTPUT] key Touch the [GROUP] key "Group" is automatically selected when the original is placed on the document glass. About the offset function Offset function "ON" Offset function "OFF" This function offsets each set of copies from the previous set in the output tray, making it easy to separate sets of copies. (Offset can function for output to the centre tray or in the offset tray of the saddle stitch finisher. ) READY TO COPY. INTERRUPT OFFSET LEFT TRAY CENTRE TRAY OK 0 OUTPUT SORT Turning on the offset function The offset function operates when a checkmark appears in the [OFFSET] checkbox, which is displayed by touching the [CENTRE TRAY] key and then selecting the upper output tray. (If a checkmark doesn't appear, touch the checkbox. ) Offset width: Approximately 30 mm (1-3/10") (A3W (12" x 18") paper cannot be offset. ) GROUP Selecting the output tray When the [LEFT TRAY] key in the above illustration is highlighted, copies are output to the tray on the left side of the machine (the left tray). When the [CENTRE TRAY] key is highlighted, copies are output to the centre tray. Touch the key of the tray you wish to use for copy output. 5-5 NORMAL COPYING Automatic two-sided copying from the reversing single pass feeder When a duplex module/2 x 500 sheet paper drawer and a duplex bypass/inverter unit are installed, the following automatic two-sided copy functions are possible. The copy paper is turned over automatically, allowing easy twosided copying. NOTE Certain restrictions exist depending on the amount of memory installed and the copy settings. (See "Copy mode output restrictions" and "Specifications for memory capacity and maximum number of originals" on page 5-4. ) Original Copy The following two-sided modes can be selected 1. [. . . ] 2-8 - Large capacity tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 - Reversing single pass feeder. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 - Saddle stitch finisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 - Stand/1 x 500 sheet paper drawer. . . . . . . . . . . . . . . . . . . . [. . . ]