User manual SHARP AR-F151

[. . . ] MODEL AR-F151 FACSIMILE OPERATION MANUAL Page INSTALLATION q INITIAL SETTINGS q CHOOSING SUITABLE MEDIA q HOW TO USE THE FAX FUNCTION q TROUBLESHOOTING q SPECIFICATIONS q 1-1 2-1 3-1 4-1 5-1 6-1 GLOSSARY q INDEX q Your fax machine and the telephone system WARNING NOTICE: NO calls can be made to or from this fax during a mains power failure. WARNING -- Australian Communications Authority (ACA) regulations state that no unauthorised changes or modifications to this equipment are permitted. Note: Complies with the following standards, ACA TS001-1997, AS/NZS 3260 ACA TS002-1997 and AS/NZS 3548. These limits are designed to provide reasonable protection against interference in an installation. [. . . ] HOW TO USE THE FAX FUNCTION The stand alone fax component of your unit offers a range of sophisticated features that allow you to control image quality, reception mode, broadcasting, polling, and transmission priorities. Functions such as sending documents from memory and substituting reception into memory are possible, due to the large memory capacity. Sending Documents Setting the Document This section describes setting documents in the SPF or on the original table. When Using the SPF: 1 Confirm that there are no documents on the original table and that copying is not in progress, then gently close the original cover. Adjust the document guides to the width of your document. 2 3 Place the document face up and push it gently into the document feeder tray. The top edge of the document should enter the fax first. Original face up 4 There are two ways to send the fax: · To scan the document into memory, then dial and transmit, continue with the "Dialling and Transmitting" section. · To dial and transmit the document directly without first scanning it into memory, press the DOCUMENT key. "DIRECT SEND" will appear in the display. Continue with the "Dialling and Transmitting" section. HOW TO USE THE FAX FUNCTION 4-1 Sending Documents When placing the Original on the Table: 1 2 Confirm that there are no documents in the SPF, and open the original cover. Place the document face down on the original table. Align the document according to the original scale in the illustration below. (Line up the centre of the edge of the document with the ( ) mark. ) Original scale mark 3 4 5 Gently close the original cover. Note: When using the original table, do not set documents in the SPF. Press the BOOK SEND key. Select the document size A4 or B4 from those displayed. · You can now make resolution or contrast settings as described in the next section and dial and transmit the fax. (See "Dialling and Transmitting" in this chapter) DOCUMENT SIZE?1:A4 2:B4 6 Press the BOOK SEND key to scan the page into memory. If you have more than one document to read into memory, place the next page, and press the BOOK SEND key to read each page. 4-2 HOW TO USE THE FAX FUNCTION Sending Documents Optional Transmission Settings There are several transmission settings that you can make before dialling and transmitting a document. Resolution Your fax has four resolution settings: · HALF TONE Use HALF TONE for photographs and illustrations. The original will be reproduced in 256 shades of gray. · STANDARD Use STANDARD for ordinary documents. This setting gives you the fastest transmission. · FINE Use FINE for improved reproduction, especially with documents containing small letters or fine drawings. FINE Use SUPER FINE when you need the highest quality of reproduction. [. . . ] 2-1 Fax Duet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 Fax Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Fax Transmission Settings . . . . . . . . . . . . . . . . . . . . . 4-3 Fine Resolution Priority . . . . . . . . . . . . . . . . . . . . . . [. . . ]