User manual SHARP AR-M207E

[. . . ] The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. Money Stamps Bonds Stocks Bank drafts Checks Passports Driver's licences CONTENTS CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SOFTWARE LICENSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To resume normal operation, press the [START] key ( ). Normal operation also resumes automatically when a print job is received or scanning is begun from a computer. While in auto power shut-off mode, no keys (except the [START] key ( )) can be used. · Use this setting to select the layout pattern when two original pages are copied onto a single sheet of paper (see page 31 for the layout patterns). · When enabled, this function offsets the position of each set of copies in the output tray in copy mode, and each print job in printer mode. · When two-sided copying is performed, this function rotates the image on the back of the original. This is convenient when binding the copies at the top (tablet binding). · This setting is used to change the copy resolution in AUTO and TEXT mode from 600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is slower when high-quality mode is used. 7 LAYOUT IN 2IN1 1: PATTERN 1 2: PATTERN 2 8 OFFSET FUNCTION 1: ON 2: OFF 9 ROTATE ORIG. IMAGE 1: ON 2: OFF 7 10 AE/TEXT RESOLUTION 1: 300dpi 2: 600dpi 55 USER SETTINGS Program number Setting codes (factory default setting appears in bold) Program name Explanation 11 2-SIDED COPY MODE 1: HI-SPEED 2: NORMAL · If the memory fills up when twosided copying is performed, "NORMAL" can be selected to make copying possible. However, "NORMAL" results in a slower copying speed. · Select whether copying is only allowed when the polygon motor is rotating, or also when the polygon motor is stopped. · Set the temperature of the fusing unit when the bypass tray is used. 20 LANGUAGE 21 22 RESET FACTORY SORT AUTO SELECT 24 · CHECK OC OPEN · CHECK RSPF 1: ON OPEN (When an 2: OFF RSPF is installed. ) 25 VALID COPY WIDTH 1: A4 (8. 5x11) 2: B5R (5. 5x8. 5) 7 28 LSU SETTING 1: ON 2: OFF 29 PAPER TYPE 1: PLAIN PAPER 2: HEAVY PAPER 1: LIGHTER 2: LIGHT 3: NORMAL 4: DARK 5: DARKER 30 DISPLAY CONTRAST · Set the contrast of the display. 57 USER SETTINGS Print mode Program number Program name Setting codes (factory default setting appears in bold) Explanation 1 FORCED OUTPUT 1: ON 2: OFF · When this function is enabled, printing in printer mode will automatically continue using a different size of paper if the specified size of paper runs out in all trays. This feature does not function in copy mode. 2 USB 2. 0 MODE SWITCH*1 · This sets the USB 2. 0 data transfer speed. To obtain the fastest speed when using the USB 2. 0 connector, first verify that your computer meets the system requirements (operating system and driver), and then use this program to 1: FULL-SPEED change the USB 2. 0 mode to 2: HI-SPEED "Hi-Speed". Note that the setting should not be changed while running a TWAIN driver. (For the system requirements, see "System requirements for USB 2. 0 (Hi-Speed mode)" (p. 49). ) · If the paper runs out during printing and there is paper of the same size in another tray, this function automatically switches to that tray (excluding the bypass tray). The function can be disabled. 3 AUTO TRAY SWITCH*2 1: ON 2: OFF *1 The scanning speed increases when the USB 2. 0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably. *2 When the 250-sheet paper feed unit is installed. 58 SELECTING A SETTING FOR A USER PROGRAM 1 Press the [MENU] key and then press the [ENTER] key. In printer mode, the user programs are accessed by simply pressing the [MENU] key. MAIN MENU 1:USER PROGRAM 2 Press the [ ] key ( ) or [ ] key ( ) to select the item that you wish to configure in the USER PROGRAM items, and then press the [ENTER] key. · See "USER PROGRAM" (p. 54 to p. 58) for the program name and program code. · You can also select a program by directly entering the program number with the numeric keys. USER PROGRAM 2:PREHEAT MODE 3 Press the [ ] key ( ) or [ ] key ( ) to change the setting of the selected item. See "USER PROGRAM" (p. 54 to p. 58) for the program code. PREHEAT MODE 1:1 MIN Note · If you mistakenly select the wrong item, press the [CLEAR] key ( ) and repeat the procedure from step 2. · To cancel a setting for a user program, press the [MENU] key. 4 Press the [ENTER] key. Your selection appears briefly and then the previous screen appears. 7 Note When "AE LEVEL ADJUST" is selected in the user programs and the [ENTER] key is pressed, the automatic exposure adjustment screen appears. Adjust the exposure and press the [ENTER] key. 59 USER SETTINGS Audible signals (key entry beep, invalid key beep, base setting beep) The machine sounds three different types of beep signals: a key entry beep that sounds when a valid key is pressed, an invalid key beep that sounds when an invalid key is pressed, and a base setting beep that sounds when a setting is the same as the base setting (base settings are explained below). [. . . ] 77 Cleaning the machine - Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 - Document glass. . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 - Original cover/RSPF. . . . . . . . . . . . . . . . . . . . . 78 - Transfer charger. . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]