User manual SHARP AR-M451U

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Required in IEC-950 (EN 60 950) - Europe The equipment should be installed near an accessible socket outlet for easy disconnection. Required in Appendix ZB of BS 7002 (En 60 950) -- United Kingdom MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. [. . . ] To change the paper tray for the cover, touch the tray selection key. (In the screen example, the " TRAY2" display is the tray selection key. ) The tray selection screen appears when the tray selection key is touched. NOTES G Two-sided copying is not possible on label sheets, and transparency film. When copying on a cover, do not select a tray that has one of these types of paper. G Select the same size of paper for the covers as for the copies. 12 [When using feeder:] the automatic document Copying will start after all originals have been scanned. (The next step is not needed. ) [When using the document glass:] Replace the original with the next original and press the [START] key. Repeat this operation until all originals have been scanned and then touch the [READ-END] key. NOTES G When the pamphlet copy function is set, the twosided copying mode will be automatically selected. G If this function is used in combination with the pamphlet copy function (pamphlet stapling) and the number of original pages exceeds the number of pages that can be stapled, a message asking you to select "CANCEL", "CONTINUE", or "DIVIDE" will appear. To cancel the job, select "CANCEL". To make pamphlet copies without stapling, select "CONTINUE". (See page 5-7 of the "Operation manual (for printer)") GWhen configuring the tandem settings in the server machine, the IP address of the client machine must be entered. For the port number, it is best to use the initial setting (50001). Unless you experience difficulty with this setting, do not change it. The tandem settings should be configured by your network administrator. If the server and client machines will alternate server and client roles, the IP address of the server machine must also be entered in the client machine. The same port number can be set in both machines. 100 sets of copies 50 sets of copies 50 sets of copies 5 To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Set the number of copies with the numeric keys. Up to 999 copies can be set. When the [START] key is pressed, the copies will automatically be divided between the server and client machines. If an odd number of copies is set, the server machine will make the extra set. 1 Touch the [TANDEM COPY] key on the special modes screen. OK 1/3 ERASE DUAL PAGE COPY TANDEM COPY JOB BUILD The [TANDEM COPY] key will be highlighted to indicate that the function is turned on, and the tandem copy icon ( ) will appear in the upper left of the screen. 2 Touch the [OK] key on the special modes screen. OK DUAL PAGE COPY TANDEM COPY If an incorrect number of copies is set. . . Press the clear key and set the correct number of copies. 1/3 You will return to the main screen of copy mode. the original in the document feeder 4 Place the document glass. (page 4-3) or on RASE JOB BUILD 5-9 SPECIAL MODES 5 Press the [START] key. NOTES G To perform tandem copying, the server machine and client machine must meet certain conditions. [. . . ] 1-9 Troubleshooting -Copier operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 -Document filing function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28 -Duplex module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 -Finisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]