User manual SHARP AR-M455U DATASHEET

[. . . ] The CE mark logo label is affixed on an equipment in case that the directives described in the above sentence are applicable to the product. (This sentence is not applicable in any country where the above directives are not required. ) Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. [. . . ] · If the memory fills up when two-sided copying is performed, "NORMAL" can be selected to make copying possible. However, "NORMAL" results in a slower copying speed. Normally "HISPEED" is selected to enable fast two-sided copying. · Use this setting to set the margin width. · Use this to change the proportion of machine memory used for printer mode. · Use this setting to select whether or not holding down a key causes repeated input of the key. For keys that normally cause a set value to increase when held down (for example, holding down the [ ] key ( ) or [ ] key ( )), this program can be used to have the set value not change when the key is held down. 9 AE/TEXT RESOLUTION 1: 300dpi 2: 600dpi 10 2-SIDED COPY MODE 1: HI-SPEED 2: NORMAL 11 MARGIN WIDTH 1: 5 mm (1/4") 2: 10 mm (1/2") 3: 15 mm (3/4") 4: 20 mm (1") 1: 30% 2: 40% 3: 50% 4: 60% 5: 70% 12 MEM. FOR PRINTER 13 AUTO KEY REPEAT 1: ON 2: OFF 64 USER SETTINGS Program number Setting codes (factory default setting appears in bold) 1: NORMAL 2: 0. 5 SEC. 1: LOW 2: HIGH 3: OFF 1: ON 2: OFF Program name Explanation 14 KEY PRESS TIME · Use this setting to select how long a key must be pressed for the input to be accepted. By selecting a longer time, you can prevent settings from being changed by the accidental pressing of a key. · This sets the volume of beep signals. If you wish to change the volume of the beep signals or disable them, see "KEY TOUCH SOUND" on page 65. The beep patterns of each type of beep signal are as follows: Key entry beep. . . . . . . . . . . . . . . . . . . . . One beep Invalid key beep. . . . . . . . . . . . . . . . . Three beeps Base settings The base settings are preset standard selections for each copy setting. The base settings are as follows: Copy ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100% Light and Dark level . . . . . . . . . . . . . . . . . Centre Paper feed location . . . . . . . . . . . . . . . . . Tray 1 (Upper paper tray) AUTO ( )/TEXT ( )/ PHOTO ( ) . . . . . . . . . . . . . . . . . . . AUTO ( ) 68 8 Chapter 8 TROUBLESHOOTING AND MAINTENANCE Problems related to general use of the machine, the copy function, and software setup are explained here. Be sure to check the problem carefully before calling for service, as many problems can be solved by the user. If you are unable to solve the problem, turn off the main switch, unplug the power cord from the outlet, and contact your dealer. Note For problems related to the printer and scanner functions, see the online manual. DISPLAY MESSAGES When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the indicated page. Note Be sure to use only genuine SHARP parts and supplies. Indication Lamp indicator Display BYPASS : ADD PAPER Tray TRAY<*> : ADD location Blinks PAPER indicator CLOSE PAPER TRAY<*> CLEAR PAPER JAM. [. . . ] : Electric discharge, throwing into fire. : Oxidizing Materials : CO, CO2 and NOX : None 11. TOXICOLOGICAL INFORMATION Acute Toxicity Ingestion(oral) Inhalation Dermal Eye irritation Skin irritation Skin sensitizer Mutagenicity Carcinogenicity : LD50 > 2000mg/kg (Rats) : No data : No data : Not an irritant (Rabbits) : Not an irritant (Rabbits) : No sensitization : Negative (Ames Test) : In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. [. . . ]