User manual SHARP AR-NB2

[. . . ] MODEL AR-NB2 AR-NB2 N NETWORK EXPANSION KIT SOFTWARE SETUP GUIDE (for network printer) Page · SAFETY STANDARDS · INTRODUCTION · BEFORE INSTALLATION · SETUP IN A WINDOWS ENVIRONMENT · SETUP IN A MACINTOSH ENVIRONMENT 2 4 6 11 25 AR-M160/M205 SAFETY STANDARDS <AR-NB2> This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. <AR-NB2/AR-NB2 N> This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] In Windows 95/98/Me/NT 4. 0/2000, double-click "My Computer" and then double-click the CD-ROM icon. Double-click the "setup" icon ( ). 6 Click the "Printer Driver" button. To view information on the software, click the "Display Readme" button. Windows 3 Note If the language selection screen appears after you double click the "setup" icon, select the language that you wish to use and click the "Next" button. (Normally the correct language is selected automatically. ) 7 8 Click the "Next" button. 4 The "SOFTWARE LICENSE" window will appear. Make sure that you understand the contents of the license agreement, and then click the "Yes" button. Read the message in the "Welcome" window and then click the "Next" button. Click the "Standard installation" button. 5 - 14 - INSTALLING THE SOFTWARE 9 Printers connected to the network are detected. Select the machine and click the "Next" button. 12 Select whether or not you wish the printer to be your default printer and click the "Next" button. If you are installing multiple printer drivers, select the printer that you wish to use as your default printer. If you do not wish to set either printer driver as the default printer, select "No". Begin installation of the printer driver. Caution 13 Note If the machine is not found, make sure that the machine is powered on and connected to your computer and then search again. If the machine is still not found, use the custom installation procedure to directly specify the IP address (p. 16). If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". Windows 14 15 When "The installation of the SHARP software is complete" appears, click the "OK" button. Click the "Close" button. 10 11 A confirmation window appears. Check the contents and then click the "Next" button. When the printer driver selection window appears, select the printer driver to be installed and click the "Next" button. Select the checkboxes of the printer drivers to be installed. Note After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer. This completes the installation of the software. · After installation, see "CONFIGURING THE PRINTER DRIVER" (p. 24) to check the printer driver settings. · To install the Printer Status Monitor or Printer Administration Utility, see the following pages: Printer Status Monitor: p. 20 Printer Administration Utility: p. 21 If you installed the PS printer driver, the PS display font can be installed from the "PRINTER UTILITIES" CD-ROM that accompanied the PS3 expansion kit. (p. 22) Note Note To use the PS printer driver, the PS3 expansion kit must be installed. - 15 - INSTALLING THE SOFTWARE CUSTOM INSTALLATION If you wish to install the display font or specify the machine's IP address when installing the printer driver, select "Custom installation". 1 2 Insert the network expansion kit "Software" CD-ROM into your computer's CD-ROM drive. Click the "start" button, click "My Computer" ( ), and then double-click the CD-ROM icon ( ). In Windows 95/98/Me/NT 4. 0/2000, double-click "My Computer" and then double-click the CD-ROM icon. Double-click the "setup" icon ( ). 7 8 Click the "Next" button. Click the "Custom installation" button. 3 Windows Note If the language selection screen appears after you double click the "setup" icon, select the language that you wish to use and click the "Next" button. [. . . ] Click the "Add" button. 5 The name of the machine that appears is the name that was entered in the AppleTalk settings when the network settings were configured ("xxxxxx" is a sequence of characters that varies depending on your machine). Click "Add". 8 Select "Sharp" in the "Printer Model" menu. The PPD file selection window appears. - 28 - CONFIGURING THE PRINTER DRIVER 9 Select the PPD file of the machine. 13 Set the printer configuration based on the options that have been installed, and then click the "Apply Changes" button. If not, printing may not be executed properly. 10 11 Click the "Add" button. The machine is added to the list of printers. [. . . ]