User manual SHARP AR-C330

[. . . ] MODEL AR-C330 DIGITAL FULL COLOR COPYING MACHINE , KEY OPERATOR S GUIDE Page · KEY OPERATOR CODE NUMBER · KEY OPERATOR PROGRAMS · KEY OPERATOR ASSISTANCE CALL 2 4 36 33 This KEY OPERATOR'S GUIDE contains information on all of the programs for use by the key operator. The programs allow the key operator to tailor many functions of the AR-C330 for specific modes of operation. These programs can only be accessed after a key operator code number has been entered. Please familiarize yourself with this entire guide. [. . . ] To enable the stapler, press the check box of this program again to clear the check mark in the check box. Disabling of Covers Mode This program is used to prevent selection of the COVERS mode. To disable the COVERS mode, press the check box of "DISABLING OF COVERS MODE" to display a check mark in the check box. To enable use of the mode, press the check box of this program again to clear the check mark in the check box. Disabling of PC/Modem Access This program is used to determine whether persons other than persons who know the key operator code number will be permitted access via a computer or other equipment, either directly or through a telephone line, to the copier's key operator programs. To require key operator code entry for access to key operator programs, press the check box of "DISABLING OF PC/ MODEM ACCESS" to display a check mark in the check box. To permit remote access to key operator programs without key operator code entry, press the check box of this program again to clear the check mark in the check box. NOTE: The customers must choose the setting of this program by themselves. If this program is not set, external operators can access the key operator programs from a computer or other equipment without key operator code entry. If this program is set, external operators must enter the key operator code to access the key operator programs. (This program is set in the factory default setting. ) 20 KEY OPERATOR PROGRAMS Disabling of Sleep Mode The sleep mode is used to turn off the power to the fusing unit automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. This mode lowers the user's electricity bill, reduces waste of natural resources, and cuts down on environmental pollution. Depending on how the machine is to be used, you may wish for some reasons to disable this mode. This can be done using this program. NOTE: Since we would like you to fully understand the purpose of this mode, we suggest that you enable this mode and set the most appropriate time using program "SLEEP MODE SETTING" (page 16). To disable the auto power shut-off mode, press the check box of "DISABLING OF SLEEP MODE" to display a check mark in the check box. To restore the mode, press the check box of this program again to clear the check mark in the check box. Disabling of Pre-scan in B/W Copy This copier performs a pre-scan in black/white copying to check the density of background of the original. The pre-scan operation allows cleaner copies to be obtained but copying speed will be slower. This program is used to disable pre-scan in black/white copying. To cancel pre-scan in black/white copying, press the check box of "DISABLING OF PRE-SCAN IN B/W COPY" to display a check mark in the check box. To restore pre-scan, press the check box of this program again to clear the check mark in the check box. 21 KEY OPERATOR PROGRAMS Registration Adjustment This program is used to adjust registration if deviation of registration of characters or lines occurs in color copying or printing. NOTE: This program can be selected by pressing the "REGISTRATION ADJUSTMENT" key on the category menu screen. KEY OPERATOR PROGRAMS COPIER MODE OTHER FUNCTION SETTINGS ENABLE/DISABLE SETTINGS OK TIMER SETTING REGISTRATION ADJUSTMENT AUTO COLOUR CALIBRATION 1. Select the "REGISTRATION ADJUSTMENT" key on the category menu screen. G The following display will appear. KEY OPERATOR PROGRAMS OK REGISTRATION ADJUSTMENT USE A4 OR 81/2 11 PAPER FOR THIS ADJUSTMENT. PRESS [EXECUTE] TO PRINT THE TEST PATCH. EXECUTE 2. 3. Press the "EXECUTE" key. G The copier will print the test patch. After the test patch is printed, place it on the document glass of the copier with 10 white sheets of the same size on top of it and press the "EXECUTE" key again. G G G G Place the test patch on the document glass as shown in the illustration. The copier will start scanning the test patch on the document glass and the adjustment will automatically be made. Place the test patch so that the mark on the test patch is positioned to the mark on the document glass that indicates the center reference point. If a scanning error occurs frequently, the test patch may be smudged. Press the "OK" key to return to step 1 and print a new test patch. Then, repeat this step. 4. Press the "OK" key to exit the program. G To re-execute the registration adjustment, repeat all the steps. 22 KEY OPERATOR PROGRAMS Auto Color Calibration The Auto Color Calibration program enables automatic color gradation correction when it becomes misadjusted. NOTE: The color gradation may not be sufficiently corrected after one correction cycle. If so, a re-execution of the program may be necessary. [. . . ] The lists printed with the key operator programs are included in "SELF PRINTS". When the "TOTAL COUNT" key is pressed, the following display will appear. KEY OPERATOR PROGRAMS TOTAL COUNT PRINT OK COPIES : 600, 000 SELF PRINTS : (COLOR) (COLOR) COPIES : 500, 000 SELF PRINTS : (B/W) (B/W) DUPLEX : 500, 000 PRINTS : (COLOR) DOCUMENT : 600, 000 PRINTS : FEEDER (B/W) STAPLER : 500, 000 SCANNER : MODE 500, 000 500, 000 500, 000 800, 000 800, 000 The total counts for all units in use will be displayed. To print these counts, press the "PRINT" key. Press the "OK" key to exit the program. Program List Printout This program is used to print out the list of available key operator programs. [. . . ]